Posts: 4,515
Threads: 425
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
As some may know the New England Vintage Electronics Club had our meet today in New Hampshire, though the morning looked promising a very pretty Sunrise the day was cool and overcast for the meet. Despite that many tailgated their wares and we had good crowds in the hall and in the Parking lot tailgating area. I think the tailgating is getting more popular due to not having to haul your goods all the way from lot to the hall just set up by your car, van, etc..... A high light was when of our members flew over several times in a Helicopter quite low at times to film the overhead view of the event, perhaps I can post when available.
At the meet a senior club member and a true gentleman in the hobby approached me with a FADA 195 A from the early 20's? Asking my help in locating a schematic, I have looked on line but no luck. We did meet another fellow a NJARC member who had worked on that set some time ago and offered some pointers, but also said he could not find a schematic.
So to these in this esteemed group, can any one render some assistance?
I am much obliged.
Paul
Tubetalk1
Posts: 2,575
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
cant help here have lot of fada schematic's but nothing on 195a
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Posts: 4,515
Threads: 425
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
Thanks Sam, it is an oldie, way back machine.
Paul
Tubetalk1
Posts: 4,950
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
Paul;
I have a Fada 175A, and I could not find a factory diagram for it either, but I found one that someone had made by tracing out the wiring in the set, in my case it was a 1924 model. One way you can often tell is that 1924-25 and earlier sets will have UV bayonet style sockets, but the 1925-26 and newer models will have UX style four pin style.
The 192A was also known as the "Neutrolette", which I think was intended to be an economy model, unlike the Fada 175A there is a diagram in either the first Riders volume, or in one of the Gernsback books, it's a 1925 model. Five will get you ten that one or both of the audio interstage transformers are open circuit, my 175A still has the originals, one is good but the other is open circuit on one winding. Here is a site that has some of Gernsback;s books posted, as well as lots of early radio books and magazines, if you want to look:
https://www.americanradiohistory.com/
Regards
Arran
Posts: 2,575
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
arran
here is a copy of 175 same as 185
https://documentcloud.adobe.com/link/tra...f428ea762b
lol ok so it copied whole section 175 is 13-10
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Posts: 4,950
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
Sam;
Those are at least a decade newer, my 175A is a three dial TRF from 1924, it's from the original F.A.D.Andrea company, before Frank sold the company.
Regards
Arran
Users browsing this thread:
|
Recent Posts
|
Part numbers to model cross
|
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM |
Restoration of the Canadian General Electric A-87
|
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM |
Restoration of the Canadian General Electric A-87
|
Great job on the cabinet.
PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM |
Part numbers to model cross
|
This document has at least some tables of models and parts used.
Example: Choke 32-7572, used in 604 radio.
Search f...morzh — 08:19 AM |
Restoration of the Canadian General Electric A-87
|
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM |
Restoration of the Canadian General Electric A-87
|
Well... While the varnish is drying up, I started repairing the chassis...
Of course I started by replacing the pa...RadioSvit — 07:12 AM |
Philco Model 38-7: what caps & resistors do fail typically?
|
Hello Martin,
Welcome aboard our little community what great Model 38-7
Sincerely Richardradiorich — 12:30 AM |
Philco Model 38-7: what caps & resistors do fail typically?
|
Welcome to the Phorum Martin.
I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM |
Part numbers to model cross
|
Jim,
We have this index put together by Dale Cook but I don't think that is quite what you are looking for.
The Parts...klondike98 — 09:37 PM |
Philco Model 38-7: what caps & resistors do fail typically?
|
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM |
Who's Online
|
There are currently 1168 online users. [Complete List] » 1 Member(s) | 1167 Guest(s)
|
|
|

|