1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Quick help
1230AM
Junior Member
**
Posts: 8
Threads: 3
Joined: Feb 2020
City: Louisville State, Province, Country: KY
#1

02-11-2020, 01:41 PM
At the risk of a violation - In addition to my prior Low AM Volume question, (On a Philco) I have a non-Philco radio with a Numite Condenser Cat. No. AT 8450 reading cap.8 and 450v.  Just to be clear, is this merely an 8mf capacitor?

Radio has a hum and this is the only cap not replaced.  Its a large one and I suspect this to be the issue.

Thank you and my apologies for posting a non-Philco question.....But this hopefully is generic and will be the last non-Philco question I ask.
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,305
Threads: 270
Joined: Dec 2009
City: Roslyn Pa
#2

02-11-2020, 01:49 PM
I would think that it's an 8mfd. An .8 would pretty small in physical size by comparison. 10mfd would be a suitable replacement as I don't know if the 8's are a common value anymore. Old school tubular 8mfd@450v would be abt 1" in dia and 2 to 3" long.
Here @ the Philco Phorum we are a non discriminatory radio phorum however we do have a special section for "other radios"
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 02-11-2020, 01:55 PM by Radioroslyn.)
Find
1230AM
Junior Member
**
Posts: 8
Threads: 3
Joined: Feb 2020
City: Louisville State, Province, Country: KY
#3

02-11-2020, 03:32 PM
Thanks!  What you describe would be it.  Thanks again for the confirmation.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread:
[-]
Recent Posts
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM

[-]
Who's Online
There are currently 1138 online users. [Complete List]
» 1 Member(s) | 1137 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration