Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 90 bezel
#16

Moved to Philco Home Radios since the current discussion has nothing to do with cabinet restoration.
#17

Radioroslyn Wrote:Didn't mean that it was hard to tune but you mention the blasting effect. It's beastly like the 70. Living near Philly there are a lot of strong stations and at night avc make tuning around much more pleasant.

Understood. Where I live, there is only one AM station close by (10 or so miles), the rest are at a distance of 40, 50 miles or more. It doesn't help that I live in a low-lying area, so radio signals are difficult to pick up here. Therefore, the "blasting" effect isn't so bad for me - only the lack of good signals due to the terrain, and the horrendous noise across the AM band here also.

The only AM listening I do anymore is to my home Part 15 transmitter. The rest is unlistenable due to the noise and weak signals. (The station 10 miles away runs an all-Spanish language format which, not knowing the language, I have no interest in.)

I do the majority of my AM listening with my RCA C15-3. The oldies sound great on it, even though it is not a "High Fidelity" set. Icon_thumbup

--
Ron Ramirez
Ferdinand IN
#18

Ron Ramirez Wrote:The pertinent issues (there were three parts) are July 1994, May 1995, and July 1995.

These are available on the wonderful World Radio History website.

Ron -

Thank you very much for posting that. It has saved me from driving a number of miles to a friend's house (I was just there yesterday to pick up some parts which he got for me at Kutztown) or asking him to scan them.

Dale H. Cook, GR/HP/Tek Collector, Roanoke/Lynchburg, VA
https://plymouthcolony.net/starcity/radios/




Users browsing this thread:
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently no members online.

>