Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Clear Schematic for 41-255
#16

RossH -

Were you looking at our copy of the 1941 Yearbook, or one that you found elsewhere?

Dale H. Cook, GR/HP/Tek Collector, Roanoke/Lynchburg, VA
https://plymouthcolony.net/starcity/radios/
#17

Ross, sorry, clicked on the wrong one. here's the down load for the 41-255 as an attachment.


Attached Files
.pdf Part44-Philco 1941 RMS Year Book.pdf Size: 1.35 MB  Downloads: 92
#18

What's really funny is I looked at the pages and saw 255 and it took me 30 sec of looking at the schematic trying to figure out why it wasn't matching what I had before it dawned on me - I had transposed the numbers in my head.

This is perfect. Besides starting to work on one of these I am going to recreate this schematic from scratch. I've done a few ten others but this will be my first Philco recreation. I'll post when it's completed and gone over a few times. 

Thank you very much for your time and consideration in doing this, and a big thank you to all who chimed in.

When you unsolder what has been soldered before the unsoldering, the unsoldering of the soldered is what will be.
#19

Hello Ross,
We have all been there don't worry the guys here have you taken care of !!
Sincerely Richard
#20

Hi Ross,
I don't know if you still need a clear schematic for the 41-255 but here is one that I cleaned up. I added pin numbers on the tubes and corrected 2 part #s (#29 and 33 were reversed on the schematic). Also, voltages are in dark red, and where provided, I color-coded the wire color name.
Fran


Attached Files
.pdf Schematic-pdf.pdf Size: 1.37 MB  Downloads: 100
#21

AH Just noticed 1 error on my cleaned-up schematic...
Part # 27 - the 8uf electrolytic cap...The lead that is marked RED should read GRN (green). Old eyes are not what they used to be!
Fran
#22

Thank you, Fran. I'll add it to the mix.

When you unsolder what has been soldered before the unsoldering, the unsoldering of the soldered is what will be.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2143 online users. [Complete List]
» 2 Member(s) | 2141 Guest(s)
AvatarAvatar

>