Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA T8-14
#1

Just got a "parts" T8-14 from an ARF deal, and was able to combine the speaker and a couple of tubes from it with my own T8-14 to produce a great looking and especially sounding set. This is an 8 tube, single 6F6 output/6F5 driver, 5Z3 rectifier 4.5 watt max output set. Additionally, I discovered that my set had an 80 where the 5Z3 belongs, so the "donor" 5Z3 was especially welcome.
#2

A T8-14 was one of my first radio finds and still have it. Nice sounding and good looking set that I learned alot of the basics on. Does your set have the globe tuning knob still? Also curious if there are any knob labels on the cabinet other than the RCA Victor logo.... mine are either worn away or never had em and the logo is pretty faded. Otherwise it's a nice original survivor.

- Mike
#3

Hello, Mike: both cabinets only had the RCA logo on them, nothing else. Fortunately, both sets had the complete set of knobs including the "globe" knob. I just commented on your collection and especially the RCA sets. Pretty neat collection you have!!
The reception of my T814 is super. It is funny that these sets do not seem to be very popular on eBay and other radio sites.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>