Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

80 Jr. pilot lamp # needed.
#1

Picked one up last week. It's a screw in, schematic shows it #24, but no part list is attached to the download from nostalgia.
#2

The modern equivalent is #46.

You can find a handy pilot lamp cross reference at Chuck's site.
http://www.philcorepairbench.com/lamps.htm

--
Ron Ramirez
Ferdinand IN
#3

Thank you Ron. I have the list in my printed files.
#4

So how's it coming? Just got a pair of 84's going here. They are the updated version of the 80 I was lucky on one of them just needed the filter cap and the ant coil rewound. The other one needed the filters, all the paper caps, a few resistors, the ant and osc coil rewound. Both also had bad grounds at the tube sockets.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Hi Terry!
It's going good so far.Cleaned the chassis up and I changed the 2 electrolytics and the power cord, and it's up and running. I'm now rebuilding all the bakelites and checking/replacing the resistors.I cleaned up the cabinet,and ordered some cloth from John. I'll let you know if I need some help...again. Icon_shifty




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently no members online.

>