Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Found a 625 today
#1

Don't know if I paid too much for it but I don't think its in all that bad of condition. One electrolytic was replaced at one time I think, $55

[Image: http://i248.photobucket.com/albums/gg187...012001.jpg]

[Image: http://i248.photobucket.com/albums/gg187...012002.jpg]
#2

I think you did very well indeed for $55. Icon_thumbup

--
Ron Ramirez
Ferdinand IN
#3

Darn good shape! Ya dunn real good.
A rather hard model to come across too.

Icon_thumbup

Chuck
#4

So what is the difference between a 625 chassis and a 620? The wavelengths covered? I noticed that like a 620 it doesn't have a shadowmeter like a 630 would.
Regards
Arran
#5

It doesn't have a power transformer either, it's the AC/DC version of the 620.
Terry
#6

So take the usual isolation transformer
precautions and procedures with this hot-chassis set.

Chuck
#7

This isn't an AC/DC set, it uses a small, low profile power transformer. You can (barely) see the top of it to the left, behind the 80 tube, in Jim's second photo.

Arran, the 620 and 625 cover the same frequencies. There are differences in the circuitry, chiefly in the AVC circuit. The 625 also has a moving shadow mask behind the dial scale, with three holes that allow the greatest illumination only to the band in use.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM

[-]
Who's Online
There are currently 888 online users. [Complete List]
» 1 Member(s) | 887 Guest(s)
Avatar

>