Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

philco 16 b
#1

    I NORMALLY DONT KEEP STUFF THIS OLD OR POST ON THIS FOURM BUT I JUST GOT THIS 16 B OFF OF CRAIGS LIST FAIRLY CHEAP MY BUDDY TA FORBES HAS TALKED ME INTO KEEPING IT .I WAS WONDERING IF ANYBODY HAD ANY ADVICE IN RESTORING THESE I BUY A LOT OF RADIOS AND THIS ONE IS PLAYING AND VERY CLEAN. I WILL RECAPP IT TOUCH UP THE CABINET .LOOKING FOR LITTLE HINTS
#2

Sounds like you know what you're doing. Very nice set. I now replace all the small carbon resistors and pilot lamps while doing a recap job - cheap, easy, and eliminates many points of future failure. Makes a big difference when touching up the alignment.
#3

Henry, that set's finish is pretty nice!!! Just make it electronically sound and enjoy!!!
#4

There is a fellow on You Tube (Lockmeister is his handle) that restores one of these, I don't remember whether it was the five or the four band version but search for his videos on restoring one of these. One thing that goes out sometimes, in addition to the usual capacitors and carbon resistors, is the coil for the shadowgraph. They also have an audio interstage transformer which can go open, but this is something that can happen with any set employing a push pull output stage, so check the continuity on both windings, especially the primary. I've worked on a 116 but not a 16, and the restoration is definately a lot more involved then your typical five or six tuber.
Regards
Arran
#5

I have a 16B this is one the best radios I have...5 bands. Shadowgraph doesn't work but boy does it receive. I refinished the cabinet and it turned out beautiful.


Attached Files Image(s)
   
#6

Icon_thumbup +1.

Henry has one of the better Zenith Collections out there, in addition to several other VERY nice sets. Plus he has a large collection of "Plastic Radios" of which I know nothing. He's a pretty good picker- among other things he has found two Waltons sets in the past year.

Sooo... it is great to see him with this Philco!!! Maybe it's the start of something good?

Oh yes, Henry, if you DO want to sell your 816K, I DO know someone who will buy it from you......
#7

Thats a nice 16B. I'd leave the cabinet as is Icon_thumbup




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM

[-]
Who's Online
There are currently 878 online users. [Complete List]
» 1 Member(s) | 877 Guest(s)
Avatar

>