Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-62 restoration
#16

Bob, that radio chassis looks great. I wouldn't mess with it. Nice job on the "old lady", she should show a little of her age. As for the TV chassis, that looks terribly nice. I can't imagine doing that deep a teardown but then again, it looked like it had seen a lot of mouse activity. You are very talented.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#17

Thanks! That TV chassis was by far the nastiest project I've tackled so far. Under the mouse droppings, I found deep corrosion. Almost right through the chassis in areas. That's why I used primer and bondo to fill it in. The set isn't particularly valuable or anything - I just wanted to see if I could do it Icon_smile
#18

Bob,

You do really nice work. After following your You Tube videos on this same radio, it's nice to see the "book" version. I always learn something when I watch/read about your restorations.

I liked your method for fixing the cabinet break. I never would have guessed it would work so well. That radio is going to look beautiful when you're done.

Tom
#19

Thanks! I'll throw up a video on the cabinet restoration when it's a little further along.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 950 online users. [Complete List]
» 1 Member(s) | 949 Guest(s)
Avatar

>