Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1953 Philco A-T2279
#1

[font=Times New Roman][align=left]I have been visiting my mother this week, and at some point we began talking about the old Philco. I thought we had gotten it in 1955, but I looked it up and it is a 1953 model. I realize now that this was a HUGE set for back then! With the cabinet doors closed it looks unobtrusive, except for the finish on the cabinet. ((Yes, it is in the living room still.) While it has provision for external antenna hookup, it also has an internal antenna handle, top center of the back. Four positions, though they never did much... we needed rabbit ears for our Brooklyn apartment. It is still intact, mostly... my father and I replaced giant capacitors or resistors (do not recall which) when it was nine. Can still function, though it has a hard time doing vertical hold. That was never one of its strong points, though.
Here is a question that has bugged me since I was a kid: this TV has a 2 through 13 VHF tuner, but a metal plate between the left pair and right pair of control knobs, proclaims UHF. Why? It has no UHF tuner nor, as far as I have ever been able to find, any place for one to plug in.
#2

UHF was an option. At the time, your Philco dealer could have installed a UHF tuner. There is likely an unused socket somewhere on the chassis. This would be where the UHF tuner would have plugged in. As far as the vertical, Philco loved micamold caps. These were just as unreliable as the paper and plastic caps they used.

I restored a similar era Philco with new mylar and electrolytic caps. It performed like it was supposed to. If you have any questions or would like it restored, email me.

Visit the world's worst TV restoration website.

http://evilfurnaceman.tripod.com
#3

    Thanks for the info! I will try to attach a pic of that center plaque. (It sits in front of a routed out rectangle.) I am still "rediscovering" the quirks of the set by chatting with my mother and my sister. I do recall that it was given two reprieves: at one point my father wanted to turn the cabinet into a bar; at another point, he was considering making it into an aquarium. Neither idea panned out, so it was never gutted. I also have to chat with my cousins upstate: their parents had a slightly different model. Two differences: different speaker cloth, and there was an empty plastic case behind the UHF panel. (Ours did not swing down.) I know that I've is still in an outbuilding in their farm.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
5U4 vs 5Z4 tubes
Well this is a Hallicrafters SX/9 circa 1936. No real issues so far although I dodged a real bullet with a cap that was...bridkarl — 07:59 AM
5U4 vs 5Z4 tubes
The pinout is the same but the 5U4 has a 3 amp filament, verses 2 amps or less on the 5Z4. I think that the pinout of a ...Arran — 12:04 AM
Philco 42-345 Restoration/Repair
By the way. osanders0311 Take a look here: Dial cord stringing Guides May be here you can fount correct string settin...Vlad95 — 11:15 PM
5U4 vs 5Z4 tubes
5U4 and 5Z4 almost identical. I think nothing happened if you left 5U4 instedad 5Z4 long time. Just heater current 5U4 ...Vlad95 — 11:02 PM
Philco 42-345 Restoration/Repair
Hello Vlad95 , Very Funny ! Sincerely Richardradiorich — 11:01 PM
Philco 42-345 Restoration/Repair
RodB You are European yourself   :evil: I'm Canadian for the last 30 years  :snowman: But not Yankee  :lol: Vlad95 — 10:49 PM
Philco 42-345 Restoration/Repair
The band switch selects different oscillator coils for the band selected. I would look for a bad connection in the switc...RodB — 10:31 PM
Philco 42-345 Restoration/Repair
Hang in there...PaulPaul Philco322 — 09:30 PM
Philco 42-345 Restoration/Repair
The thrill is gone again, thought I was close to being done with it. Well Friday it was receiving broadcast, Saturday mo...osanders0311 — 07:47 PM
Help with Supreme 599
Iam getting closer to fixing it. I bumped Up the tranny voltage to get 5v on the 80 tube. I gan get the needle to move ...daveone23 — 03:41 PM

[-]
Who's Online
There are currently no members online.

>