Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Catedral 84B e 37-60 medidas gabinete
#1

I am needing the measures of these 03 radios philco, width x height x depth, ok obliged sds
jucapank

Estou precisando das medidas destes 03 radios philco, a largura x altura x profundidade,

ok obrigado
sdsjucapank
***********
Philco catedral 1937 mod 37-60
http://radioatticarchives.com/images/p/P...tanley.jpg

the 1934 Philco catedral mod 84B

http://radioatticarchives.com/images/p/P...bSmith.jpg

the Philco 1930 MOD 20
http://radioatticarchives.com/images/p/P...ombini.jpg

**********************
#2

I obtained the measures of Philco 37-60 are these;

width 43cm x height 33,5cm and depth 22,5cm

it lacks the main one that he is 84B
sds
jucapank
#3

please
width 33,5cm x height 43cm and depth 22,5cm
ok!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
#4

It would like to know on the painting, covering, texture of Philco 37-60, the original painting has a effect FAUX, a type of spot, in the front, what it wanted to know is if the laterals also use this effect spot faux?
sds
jucapank
************************************
texto original sem tradução:
Gostaria de saber sobre a pintura, revestimento, textura do Philco 37-60, a pintura priginal tem um efeito FAUX, um tipo de mancha, na frente, o que queria saber é se as laterais também usa esse efeito mancha faux?
sds
jucapank
#5

Um colecionador me forneceu estas medidas para o 84 são elas, 35 x 43 x 22 (dizem que somando as 3 medidas dá exatamente 1,00m) dizem que era baseado em adotar o sistema metrico em cm..por ter sido lançado no mercado brasileiro), mas não sei se isso é verdade.
Por coincidência o modelo 37-60 é as mesmas medidas, e estas que postei tinha um dos lados com 0,5cm creio que a mais ( o gabinete era reformado ou replica, da pessoa que forneceu estas medidas e aí deve estar o erro de 0,5cm a mais...
sds a tds vcs,
jucapank




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2152 online users. [Complete List]
» 1 Member(s) | 2151 Guest(s)
Avatar

>