Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

I think I'll pass on this one...
#1

Over the weekend, my wife and I did some antique shopping, and in one shop I saw a Philco 37-38 shouldered tombstone battery radio.

Here's what was done to it - the photo finish was completely stripped off (looked like plywood!), the grill cloth was replaced with something that was purple burlap, and they wanted $80 for it!

At least it was marked down from $100 to start.

No thanks. Icon_sad

Bill

Sent from my Pentium II on the AT&T Dial Network
#2

You could have asked them if there was a typo on the price tag, as in $80 instead of $8. Icon_razz

--
Ron Ramirez
Ferdinand IN
#3

Antique stores never cease to amaze me. A lot of them seem to think because something's "old", it has to be worth a fortune. I'd say the biggest laugh I ever got at an antique store was a late '40s GE AA5 radio (nothing special) with a $300 price tag on it. Of course this was up around the Washington DC area.

Tom
#4

I forgot to mention - it was also mssing 2 knobs, and one of them was the tuning dual knob!

$8 would have been a fair price for it. The cabinety issues were obvious; who knows what evil lurks in the heart of the chassis? Icon_twisted

Although, if was as low as $20, I would have started thinking about it, but only then. (I'd have taken it for $15!) Icon_eek

Bill

Sent from my Pentium II on the AT&T Dial Network
#5

Get out the handkerchief, guys!

There's a flea market hereabouts that I go to a lot. A few years ago I happened to look under a table in the outside area, and recognized a Philco shoulder tombstone with a rather obvious 16/116 chassis, looking at it from behind. I looked at the front , it was a '35 vintage 16. How much, I asked? Ten bucks, he said. I didn't want to waste time negotiating, so I paid his price. I did restore it, and let it go, as I already had one.

Some times, you just have to pay the price!




Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2253 online users. [Complete List]
» 4 Member(s) | 2249 Guest(s)
AvatarAvatarAvatarAvatar

>