1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
repairing light sockets
murf
Senior Member
****
Posts: 673
Threads: 148
Joined: Jun 2011
City: Elko,MN.
#1

02-06-2016, 01:05 PM
Hi Guy's,
I know I have read a n article Ron put on here about repairing Philco light sockets, but I can't find it.
I have a 37-116 that I need to replace or repair light sockets on.
Mine is missing the original light sockets and wire harness.
I managed to find a couple light sockets with the shields that need to be re-built.
Can someone supply me with a link?
Thanks,
murf
Find
KCMike
Phorum Expert
*****
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
#2

02-06-2016, 01:15 PM
Philcoradio.com - Tech Section - Pilot Lamp Rebuilding
Couldn't post clickable link.
(This post was last modified: 02-06-2016, 01:17 PM by KCMike.)
Find
sam
Phorum Expert
*****
Posts: 2,573
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#3

02-06-2016, 01:16 PM
here
http://www.philcoradio.com/tech/lamps.htm

sam
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Find
murf
Senior Member
****
Posts: 673
Threads: 148
Joined: Jun 2011
City: Elko,MN.
#4

02-06-2016, 01:48 PM
(02-06-2016, 01:16 PM)sam Wrote:  here
http://www.philcoradio.com/tech/lamps.htm

sam

Thanks Sam and Mike.
murf
Find
Arran
Phorum Expert
*****
Posts: 4,894
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
#5

02-06-2016, 11:23 PM
  If you could find some phenolic or porcelain washers of a suitable size that would be an improvement over the nylon ones, although all are better then the rubber crap Philco used.
Regards
Arran
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM

[-]
Who's Online
There are currently 843 online users. [Complete List]
» 3 Member(s) | 840 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration