Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Lowboy 45 Speaker
#1

I have recently acquired a Philco Lowboy 45. The cabinet is in good shape, but the only thing left inside is the speaker. I tested it, it's not blown but is just really quiet. I'd just like to know more about the parameters of the speaker (power handling, impedance, etc). If anyone has anything, that'd be great. Thanks.
#2

Welcome to the Phorum!
Icon_wave

Ron has collected and posted (see the speakers.zip file) speaker information, unfortunately unless I missed it I only see the 5" speaker for the 45C model, not your 45L. Perhaps someone will have the info.
#3

It is most likely that your speaker is "quiet" because the field coil is not being charged. The old speakers did not use a permanent magnet. So without the radio to supply power it has no magnet.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#4

Good thought Russ!
#5

Before we go on a wild goose chase why don't you tell us HOW exactly you tested it.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

The 45L speaker is K-22, which is in the speaker index - only the 45L is not listed as using it.

Good catch, Bob. I'll have to correct that after K-town.

--
Ron Ramirez
Ferdinand IN
#7

  May NOT be the speaker,,could be capacitors,,resistors,,,if have not be replaced,,check tubes,,etc,,
#8

Ken

He kinda said there is only speaker in there. Implies no chassis, inferring no capacitors, resistors or tubes. Unless I am missing something Icon_lol

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#9

  Apparently,,,I missed that ALSO-------SORRY




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 716 online users. [Complete List]
» 1 Member(s) | 715 Guest(s)
Avatar

>