Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Fisher 1800 receiver
#1

  Well this was what I was hoping to get at this auction. But went too high for me.
http://bid.schulmanauction.com/lot/26234...ef=catalog
#2

I know this is going to sound crazy...but $632.51 is cheap compared to what its sibling 800-C receivers usually sell for. And I think the 1800s, being more rare than the 800-C, usually command a premium. Most likely, whoever bought this is going to flip it for double the money.

--
Ron Ramirez
Ferdinand IN
#3

Looking closely at a chassis picture with voltage/rating stamped on it, it indicates 220-240V AC!
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#4

I read somewhere that the 1800 was designed for export and/or for sale to military personnel stationed outside the USA.

--
Ron Ramirez
Ferdinand IN
#5

Thanks Ron, it might be a killer for someone here in the states to purchase unless it is easily modified? The seller might have pointed that out. KCMike , you might have been lucky to not be high bid.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#6

I seen that on the chassis and thought it would have a selector some where to change to 120v.
Learn something new everyday.
Your right Jerry, glad now I no buy.Icon_smile
#7

Mike, perhaps it is something easy but would not be a switch change or it would have listed it as a dual voltage. Someone else has bought it and I hope they know more than we do. I will yield to Ron's knowledge of these lovely receivers.
Best, Jerry

A friend in need is a pest!  Bill Slee ca 1970.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 781 online users. [Complete List]
» 1 Member(s) | 780 Guest(s)
Avatar

>