1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
B&K 600 tube tester restoration
madrescuer
New Member
*
Posts: 1
Threads: 1
Joined: Jul 2016
City: Howell,NJ
#1

10-18-2016, 08:16 PM
I was recapping the Tube tester and was having some difficulty finding a 5uf 250v electrolytic capacitor. I have a 8uf 450 volt electrolytic.Is this an acceptable substitute?
Thanks in advance!
Find
morzh
Odobenus rosmarus
******
Posts: 16,507
Threads: 572
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#2

10-19-2016, 07:52 AM
It depends where it is in the circuit.

http://www.mouser.com/ProductDetail/Corn...X1Hdo6Q%3d

http://www.mouser.com/ProductDetail/Corn...BvZ%2fE%3d
(might be OK, depends where in circuit)

http://www.mouser.com/ProductDetail/Pana...rFOO8a4%3d

etc.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
Kenneth F. Besso Jr.
Senior Member
****
Posts: 670
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
#3

10-19-2016, 06:51 PM
HOW about ,,JUSTRADIO,,,,,CANADA
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#4

10-25-2016, 12:21 PM
If it really is 8uf (test it) then it will probably be fine. The tolerance on the old electrolytics was something like -30% to +80%.
Most of the high-compliance parts in old testers are marked. If it is one of these marked parts find a close match.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
(This post was last modified: 10-25-2016, 12:23 PM by Phlogiston.)
Website Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment