1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 366 intermittent
John John
New Member
*
Posts: 1
Threads: 1
Joined: Nov 2016
City: Ottawa, Ontario, Canada
#1

12-05-2016, 12:31 PM
Canadian Philco #366 (60B USA). If I insert an audio signal just before the Type 75 and Type 42 tubes the signal appears at the loudspeaker. Inserting the signal at the volume control does not get to the loudspeaker. The radio was working, but a small pop came out of the peaker and it stopped working. Band selector switch tests okay, but quite stiff and is set to AM Standard frequency. If not a tube, then what?
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
#2

12-05-2016, 01:50 PM
Hi John and welcome,
So what if you apply an audio signal pin 4 of the 42, then to pin 2 of the 75 though a cap as there is HV at this connection and finally the the cap of the 75.
I'm assuming that the chassis has been serviced w/new caps and resistor have been checked to be within 20%.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
klondike98
Phorum Moderator
******
Posts: 5,170
Threads: 274
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#3

12-05-2016, 05:50 PM
Welcome to the Phorum!
Icon_wave
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
philco predicta
The model is the holiday without UHF It has no sound and I don't have an oscilloscope or signal generator.cgl18 — 08:51 PM
Philco model 38 code 121 not receiving signal.
I will definitely check my lead length and wire dressing. Thanks for the ideas.Stormlord5500 — 08:06 PM
Philco model 38 code 121 not receiving signal.
Do make sure that you twist the 3 wires from the chassis to the transformer, and dress away from tubes, especially audio...MrFixr55 — 07:38 PM
Philco model 38 code 121 not receiving signal.
The cone unfortunately got damaged when I removed it. The glue that held the cone to the basket was sloppily applied and...Stormlord5500 — 07:12 PM
Philco model 38 code 121 not receiving signal.
So what was wrong with the original speaker? Was the cone damaged? Unless it's totally hopeless I would put it aside as ...Arran — 05:31 PM
My collection presentation
There is an article on my site that introduces the first portable radios in my collection. I have only provided a link t...Vlad95 — 01:17 PM
Electrolytic restuffing/internals
Bridkarl This specific cap you have is the easiset type to restuff. I usually cut it at the upper border of the depr...morzh — 11:35 AM
philco predicta
Hi CGL18, First off, welcome to the Philco Phorum. I have not worked on a TV for a while but here are some givens: ...MrFixr55 — 08:22 AM
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration