1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Threaded Mode
FM motorboating on Philco 48-482
Micro9
Junior Member
**
Posts: 36
Threads: 15
Joined: Aug 2007
City: Glendale,AZ
#1

11-01-2009, 10:34 PM
Need help on a Philco 48-482.BC and SW work great after recap but FM is very weak and motorboats when volum is rasied.FM was bad before I recapped it.All resistors are with in tolerance around the FM1000 and 7B6 tube.....Any ideas????
Find
Micro9
Junior Member
**
Posts: 36
Threads: 15
Joined: Aug 2007
City: Glendale,AZ
#2

11-02-2009, 11:53 PM
FIXED.....One of the "NEW" E-caps I put in went belly-up....Checked it before I put it in..It checked good...went belly-up after the power hit it.....
Find
exray
Phorum Expert
*****
Posts: 893
Threads: 9
Joined: Mar 2008
City: Vieques, PR USA State, Province, Country: PR
#3

11-03-2009, 09:00 AM
How did you pin it down? Did it swell up or pop?

-Bill
Website Find
Micro9
Junior Member
**
Posts: 36
Threads: 15
Joined: Aug 2007
City: Glendale,AZ
#4

11-03-2009, 02:34 PM
No I used my ESR meter and started from scratch again....Per the Schematic (I) part of the old Cap went to filter the FM.I cut the orginal cap out of the ckt before I put in a new cap in its place.....The cap looked just Like new but was shorted....
Find
codefox1
Silent Key
*****
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
#5

11-03-2009, 06:29 PM
Interesting. I have seen problems with motorboating caused by an open filter capacitor quite a few times, but a shorted one would either burn up the dividing resistor or cause the stages fed by it to cease functioning. Glad you got the set working again, but I'm afraid I missed something.
Find
Micro9
Junior Member
**
Posts: 36
Threads: 15
Joined: Aug 2007
City: Glendale,AZ
#6

11-03-2009, 09:13 PM
There was a 3300 ohm R404 that was also burnt. It wasn't open but was @3.5 meg and I replaced that also....
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
That looks a lot like an aircraft connector of some kind, even if it's a U.S.N power supply. I have a book somewhere abo...Arran — 02:56 AM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
hello david, I have a similar generator in my collection that features a cast iron, single-cylinder Briggs & Stratt...radiorich — 01:00 AM
under chassis parts locator diagram for 1938 Zenith 9s262
Has anyone gone to the trouble of creating an under chassis parts locator image?  Yes, I can identify components by foll...bobloney — 08:57 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Try looking at this site the book mark is for a old generator that I was given. David    https://radionerds.com/index.ph...David — 08:36 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Hello Everyone, I am looking for voltage identification for all the pin positions on the socket of a CRV-20130 power su...Tonym4704 — 08:16 PM
Philco P45-6365 Universal Transformer Instruction Manual
Can anyone guide me to where this may be found?GRG — 03:00 PM
54C Complete Teardown/Rebuild
I don't think that I have encountered a 12Z3 before, curious how it uses one of those but includes a #43, which is a 25 ...Arran — 02:17 PM
HiFi (Chifi) tube amp build - but my own design.
It's the other forum. I'm also in DIY, but mostly read there. Honestly, I kinda jumped into this without much thought to...TV MAN — 10:43 AM
Philco 71 Code 125
Hello,  I am in need of a schematic for this radio. Mine has the three separate circular tube shields and a shadow me...dconant — 08:06 AM
Stromberg Carlson 1500 Squeal
And life just keeps getting more complicated.dconant — 07:57 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration