Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

16B volume control potentiometer
#1

I'm sure this has come up before but I can't find it anywhere, I'm looking for a replacement volume pot for my 16B, part # 33-5013 any info on what new pot to get would be helpful.  I'm finding conflicting info on values. Thanks.
#2

I suggest you try Mark Oppat at: http://www.oldradioparts.net

He has a huge selection of controls and will know the right one to use.

Jon
#3

Okay as far as I can tell the 16's started out with a 350,000 ohm pot with a tap at 30,000. that was changed at one time to a 2m with an unspecified tap. Nothing at radio daze list a tap and antique radio supply looks like all guitar stuff.
#4

http://www.oldradioparts.com/potindex.txt

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Do you have 350K or 2M part? There were changes. I got mine from Mark.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

According to the 1946 IRC Volume Control Replacement Manual:

Part #33-5013 is 350K (75K tap). IRC equivalent D18-137X.

Part #33-5022 is 2M (500K tap). IRC equivalent D13-139X.

I also got a replacement from Mark Oppat.
#7

I have seen 2 different chassis in 16B Cathedral Radios
4 band and the 5 Band which is more common in the 16B

Not sure if VC are the same

Bob T
#8

(03-19-2017, 11:57 PM)Nathan Slingerland Wrote:  According to the 1946 IRC Volume Control Replacement Manual:

Part #33-5013 is 350K (75K tap). IRC equivalent D18-137X.

Part #33-5022 is 2M (500K tap). IRC equivalent D13-139X.

I also got a replacement from Mark Oppat.

[i] I have the 33-5013, I couldn't find anything on it. I opened it up and it looks great, I pulled the one out of my 16X and apparently the pots not the problem. Both work but I'm getting less than half the volume I should at max.[/i]




Users browsing this thread:
[-]
Recent Posts
Electrolytic restuffing/internals
I don’t have a vise so I had to hold it in my hand. Not optimal but covered up by the hvac tape in the end. I have a few...bridkarl — 11:52 PM
Electrolytic restuffing/internals
Bridkarl A question. For a hacksaw the cut looks a little...jagged. Why?morzh — 11:45 PM
The list of my radio & TV collection!
As usual, an interesting post from you, Peter. This seems to be similar to the RCA 3-BX-671 and the Zenith Transoceanic...MrFixr55 — 11:41 PM
The list of my radio & TV collection!
Hello Peter, Thank you for sharing your new video and looks like your weather is nice their too. it was like 25 Cel...radiorich — 11:05 PM
Electrolytic restuffing/internals
hello bridkarl, I will post some better photos ! Sincerely Richardradiorich — 10:14 PM
Electrolytic restuffing/internals
I just taped the two pieces of the cap together, but I can see your method is better. I just held the lead in with solde...bridkarl — 08:18 PM
Electrolytic restuffing/internals
hello bridkarl, Well done ! Here is a Photo of the base of Philco capacitor that I cut open you can see how I glued th...radiorich — 08:14 PM
philco predicta
Hi CGL18, Here is a link for the schematic from the Early television Foundation: WARNING!! One side of the Chassis i...MrFixr55 — 08:09 PM
The list of my radio & TV collection!
Peter; I like Canadian General Electric sets, whilst the model numbers are often the same as their U.S General Electr...Arran — 05:44 PM
Electrolytic restuffing/internals
Did as suggested. Cut can with hacksaw, removed internals, attached new 8mf cap - with ample use of cardboard and elec...bridkarl — 03:36 PM

[-]
Who's Online
There are currently no members online.

>