Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Got another Mdl 600/Guess what's bad!
#1

The oscillator coil. Still no knobs either. Time to break out the #36 wire and have some fun! This one is an earlier version. Less louvers on the top of the cabinet and no ridges on the tuning cap for the pointer.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#2

At this rate, you're going to become an expert on the 600! Icon_lol

--
Ron Ramirez
Ferdinand IN
#3

Well I guess that will be my big claim to fame!! I think I already know too much about them.The dollar pocket watches seems the be a nice reprieve from radios and the like. Anyway my daily watcher B/W TV when up in smoke the other night. It went ZORCH and the screen went black. After taking a good look at it the filament winding for the damp tube arced over to the chaiss. Lots of HV on it. So it's getting it's own transformer. Maybe today.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread:
[-]
Recent Posts
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM
Electrolytic restuffing/internals
I have an issue on a non-Philco radio which I expect to run into on a whole set of Philcos and others. I have an 8mf ...bridkarl — 01:17 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. I thought about it and decided to put it up in the arch support. I was looking at the chassis and didn't ...Stormlord5500 — 06:24 AM
Philco model 38 code 121 not receiving signal.
Congrats on your success Stormlord. My rough guess is that since both the 15 and the 1A6 are supposed to be shielded, I...MrFixr55 — 10:04 PM
The list of my radio & TV collection!
A little light Saturday positive about our hobby in our feed... My new every Saturday video about antique radio equipme...RadioSvit — 02:12 PM

[-]
Who's Online
There are currently 724 online users. [Complete List]
» 3 Member(s) | 721 Guest(s)
AvatarAvatarAvatar

>