1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 37-650 and 70 chassis washers
Oldresistor47
Junior Member
**
Posts: 27
Threads: 4
Joined: Aug 2016
City: Pembroke Pines, FL
#1

06-25-2017, 08:48 PM
Can anyone recommend a vendor for the chassis washers of these two Philcos models, whom will not charge $4.00 a washer.
Find
morzh
Odobenus rosmarus
******
Posts: 16,510
Threads: 572
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#2

06-25-2017, 08:57 PM
Yep. Lowes or Home Depot. You could buy their grommets and trim them. If this is what you want to do.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
Oldresistor47
Junior Member
**
Posts: 27
Threads: 4
Joined: Aug 2016
City: Pembroke Pines, FL
#3

08-13-2017, 05:56 PM
Trying to finish this 37-650 and after several weeks of not working on it, I am not receiving any stations lower than 710 AM. Tried to start alignment and found AC signal just above 200 volts A/C. Procedure indicates meter should be in the 30 volt range. I have the positive on the plate of one of the audio amp tubes and negative on cathode. Any suggestions as to could be the problem. I don't get ay meter swing when adjusting comparators neither. Thanks
Find
morzh
Odobenus rosmarus
******
Posts: 16,510
Threads: 572
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#4

08-13-2017, 07:02 PM
I am not sure how you could get 200V AC across the output tuve, but myself, I always clip my meter to the output xfmr secondary (or speaker's voice coil) and measure volts.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Model 70 Cabinet Trim
musar , Well if you have any more questions feel free to post away . Sincerely Richardradiorich — 08:56 PM
Model 70 Cabinet Trim
Although I have not made any cabinets or cabinet parts for a couple of years, I still have some parts left over, includi...Steve Davis — 06:26 PM
philcorepairbench.com - shadow-meter
Thanks Ron.fenbach — 02:43 PM
Model 70 Cabinet Trim
Thank you, Gary. Before making my original post, I had clicked on "Steve Davis Cabinets" only to find that it...musar — 02:25 PM
philco predicta
Welcome to the Phorum, cgl18! I am not your resource for television repair, but lots of friendly help is available here...GarySP — 02:12 PM
Model 70 Cabinet Trim
Welcome to the Phorum, musar! You can send Steve Davis a private message (PM). The site is at the top of the Home page...GarySP — 02:09 PM
Model 70 Cabinet Trim
How do I contact him? The only contact information for him I could find when searching online was a telephone number th...musar — 10:38 AM
philco predicta
Hello, good afternoon, I would like to ask what the possible problem could be if I don't have an image on the screen. I ...cgl18 — 10:19 AM
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios