Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Kolster K-20 A.F. Transformer
#1

Hello, all.

Tried posting this on another site but didn't get any responses. Since I've always had good luck here, I thought I'd ask another newbie question: is anyone able to tell me what size A.F. transformers are used in a Kolster K-20? They are marked AFT1 and AFT2 on the schematic which can be found here:

http://www.nostalgiaair.org/pagesbymodel...040092.pdf

Thank you in advance for any help.

Dave
#2

Perhaps a couple universal output transformers like the P-T291 from AES?
#3

Hi Dave,
>able to tell me what size A.F. transformers are used in a Kolster K-20?
I'm not sure I understand what you are asking. Are you referring to physical size?? Or electrical equivalent??

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

Electrical equivalent
#5

Ok What you are looking for are https://www.tubesandmore.com/products/tr...tage-10-ma  for both. If the transformers are enclosed and have a 1/2" core you can buy just the replacement winding.

GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

Other then the generic AES transformer you could try an Edcor one, or try the solid state substitute circuit that was featured in the A.W.A Old Timer's Bulletin about ten years ago, I think it's posted online somewhere.
Regards
Arran
#7

Thank you for the help.

Dave




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Electrolytic restuffing/internals
Did as suggested. Cut can with hacksaw, removed internals, attached new 8mf cap - with ample use of cardboard and elec...bridkarl — 03:36 PM
The list of my radio & TV collection!
For fans of antique radio... My new video... How to test radio tubes on a Hickok 530B tube tester? Test radio tubes o...RadioSvit — 01:25 PM
philcorepairbench.com - shadow-meter
Thank you Billpoulsbobill — 11:53 AM
philcorepairbench.com - shadow-meter
Hi, Try here Philco Service Hints & Tips, Number 1 It's from the web archive (Way Back Machine).Keith — 10:17 AM
PT-6 finished!!
Hi Arran,  Yes, you are correct, the "nominal" voltage for these Loctal tubes was the same 6.3 or 12.6 V as...MrFixr55 — 07:48 AM
PT-6 finished!!
Actually the Loctal tube series, with number beginning with "14" are 12.6 volt tubes, at 150 ma, I'm not sure ...Arran — 02:14 AM
philco predicta
The model is the holiday without UHF It has no sound and I don't have an oscilloscope or signal generator.cgl18 — 08:51 PM
Philco model 38 code 121 not receiving signal.
I will definitely check my lead length and wire dressing. Thanks for the ideas.Stormlord5500 — 08:06 PM
Philco model 38 code 121 not receiving signal.
Do make sure that you twist the 3 wires from the chassis to the transformer, and dress away from tubes, especially audio...MrFixr55 — 07:38 PM
Philco model 38 code 121 not receiving signal.
The cone unfortunately got damaged when I removed it. The glue that held the cone to the basket was sloppily applied and...Stormlord5500 — 07:12 PM

[-]
Who's Online
There are currently 822 online users. [Complete List]
» 1 Member(s) | 821 Guest(s)
Avatar

>