1933-34 Philco 89B Restoration
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
Jumping back into this Model 89. My workshop is filling up, and I need to start fixing and selling the sets I don't intend to keep. Label on the back of this one says it is a Code 121. My other 89 that I plan to keep is a Code 123. 
I just went through my Cap stock and pulled everything.
Question: Bakelite Block 4989-W: The 200 ohm resistor: Is a 1 Watt replacement sufficient?
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 1,412
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
I would just reinstall the original wire loop. It's better than any resistor you could put in there.
Steve
M R Radios C M Tubes
Posts: 16,515
Threads: 572
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
The plate current of the 39/44 tube (if the resistor is the one in the Cathode of it in parallel with the cap) is 6mA max, which will make the dissipated power 0.007 W (7mW), which means that any small resistor will do just fine.
If you could re-use the wire resistor that was there - great. Otherwise use any power you have.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
This might be a little after the fact but those cloth covered wire wound resistors don't take kindly to flexing or movement. Typically resistance wise they are very stable and should stay in tolerance. Just don't bend it.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 670
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
Don't Breath on them,,,and no heat on ends,,,
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
I wound up replacing the resistor in the bakelite block with a 1 watt I had on hand.
This block and 1 other were done last night.
Electrolytics were replaced today.
I did a quick check of the transformer, some of the coils, and all the resistors.
All checked out, so I decided to turn it on, running it through my variac.
Here's a video I shot during the 1st power up test. All stations came in where they should on the dial.
[Video: https://youtu.be/uxNjHNX4wvs]
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
Last post, showed the radio up and running. I patched a couple pieces of missing wood in the upper part of the grill, did some touch-up work, and gave the cabinet a new coat of toner over the original, and a new grill cloth from Richmond Designs. It went to a new owner just before I left for my trip earlier in January. New owner is really happy, and I'm glad to start thinning out my workshop, and make a little money off the hobby. Here's some glamour shots before it went to its new home.
[Image: https://farm5.staticflickr.com/4578/2712...00f3_b.jpg]
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 16,515
Threads: 572
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Looks very nice, Jeff!
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 5,171
Threads: 274
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
The list of my radio & TV collection!
|
| Ok. Everything opens with a direct link. Yes. As Arran said, this is a transistor radio. It is a more expensive version ...RadioSvit — 03:07 PM |
|
Electrolytic restuffing/internals
|
| Gary
I thought the same, but then isn't a hacksaw by definition is the one with fine teeth?
>>A hacksaw is a...morzh — 03:01 PM |
|
The list of my radio & TV collection!
|
| Ah a KiJiJi seller!
I've noticed that KiJiJi tends to be where all of the rejects from craigslist go, not that there ...Arran — 01:43 PM |
|
Electrolytic restuffing/internals
|
| When I'm lazy, I use a razor knife with a new blade. Nice smooth, even cut, minimal loss of material and no trimming or ...RodB — 01:39 PM |
|
Electrolytic restuffing/internals
|
| I still disagree with your sawing or cutting method. It is much easier in terms of the opening method and better in term...Vlad95 — 01:29 PM |
|
Electrolytic restuffing/internals
|
| For the question about the jagged hacksaw cut, the most common reason is too aggressive 'bite' of the saw blade. I use ...GarySP — 01:26 PM |
|
Electrolytic restuffing/internals
|
| Well I retire in about three years. My plan is to build
a better workshop that has an area for these kinds
of things. ...bridkarl — 01:14 PM |
|
Electrolytic restuffing/internals
|
| Ido remember you telling us about your health condition.
Yes, a vise is a good thing to have. Many things I do I woul...morzh — 01:08 PM |
|
The list of my radio & TV collection!
|
| Strange, the second link works for me without problems. Try this direct link.
Or try searching for "AKKORD DELUX ...Vlad95 — 01:08 PM |
|
The list of my radio & TV collection!
|
| Looks like Peter and I have the same idea.RodB — 11:37 AM |
|
Who's Online
|
There are currently 470 online users. [Complete List]
» 1 Member(s) | 469 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
