1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
53-706 winter project
SteveinAlaska
Junior Member
**
Posts: 19
Threads: 7
Joined: Feb 2016
City: Fairbanks Alaska
#1

11-12-2018, 11:41 PM
Expecting 4 to 8 inches of snow with 30 mph winds so it looks like winter finally is here Icon_lol!
So I am starting with this little gem for the 1st winter project.
Missing the lamp, the cabinet is a little worse for the wear, but all the rest of electronics are there (chassis & clock).
Found a schematic to work with.

Questions ......... is there a specific style/type lamp assembly that I should use?
Telechron clock.......I see the Philco part# 41-2043, is there a Telechron model number somewhere?

There is a blown resistor (47000) to begin with & someone else has worked on it before. So, I start from square one on this.

I welcome any thoughts, comments & suggestions
Springtime comes about end of April around here.
Find
David
Phorum Expert
*****
Posts: 1,269
Threads: 32
Joined: Jan 2014
City: Wellborn Florida
#2

11-13-2018, 08:23 AM
   
Good morning Steve. Posting a link to a GE radio that has some good info on the clock, Please do not use WD 40 on the clock use a good light weight oil.  http://www.nostalgiaair.org/pagesbymodel...007697.pdf
Find
SteveinAlaska
Junior Member
**
Posts: 19
Threads: 7
Joined: Feb 2016
City: Fairbanks Alaska
#3

11-13-2018, 03:29 PM
....and I thank you for the help & info!
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,305
Threads: 270
Joined: Dec 2009
City: Roslyn Pa
#4

11-13-2018, 06:47 PM
Not sure which lamp you are referring to? The pilot lamp is going to be a #47 and the 120v lamp I would use something 40w or less incandescent. LED's might generate noise.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
SteveinAlaska
Junior Member
**
Posts: 19
Threads: 7
Joined: Feb 2016
City: Fairbanks Alaska
#5

11-14-2018, 02:47 AM
Sorry 'bout that - it's the 120 volt lamp I was wondering about.
Did Philco make (or use) a particular type or brand of lamp base??
Find
David
Phorum Expert
*****
Posts: 1,269
Threads: 32
Joined: Jan 2014
City: Wellborn Florida
#6

11-14-2018, 08:30 AM
OK so I am half blind. The only light I see is the number 47 bulb hooked to pins 4 an 6 of the 35W4
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,305
Threads: 270
Joined: Dec 2009
City: Roslyn Pa
#7

11-14-2018, 11:44 AM
This particular model has a dial lamp, a clock, and is a desk lamp/ am radio.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Ok MrFixr55,  I have tried the DeoxIT D5 on the band switch and even though it has relieved the tension I felt when turn...osanders0311 — 11:11 AM
Part numbers to model cross
Is there a reference somewhere where you can punch in Philco part numbers and see what models those parts were used in?Jim Dutridge — 10:17 AM
Philco 42-345 Restoration/Repair
Hi OSanders, Look carefully at the band switch. Turn it slowly and "wiggle" it around the desired band. ...MrFixr55 — 12:33 AM
5U4 vs 5Z4 tubes
I think that RCA and GE introduced metal tubes in the USA in 1936.  I don't know if they were being made by RCA, GE or b...MrFixr55 — 11:20 PM
Philco 42-345 Restoration/Repair
Vlad95, Thank you for the stringing guides and wow there are so manyosanders0311 — 06:01 PM
5U4 vs 5Z4 tubes
A pre war Hallicrafters, and an early one too, very nice! 1936 is pretty early for metal tubes too, which would explain ...Arran — 05:58 PM
Philco 42-345 Restoration/Repair
Thanks Rod, "When you hear the background hiss and no station it usually indicates that the oscillator quit" ...osanders0311 — 05:52 PM
Philco 42-345 Restoration/Repair
RodB :beerchug:Vlad95 — 10:22 AM
Philco 42-345 Restoration/Repair
Vlad, you nailed it. Swiss and German roots.RodB — 09:54 AM
5U4 vs 5Z4 tubes
Well this is a Hallicrafters SX/9 circa 1936. No real issues so far although I dodged a real bullet with a cap that was...bridkarl — 07:59 AM

[-]
Who's Online
There are currently 472 online users. [Complete List]
» 1 Member(s) | 471 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration