Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Another Philco save.
#1

Hi,

I found the following radio in my favorite junk store this past Friday:-

[Image: http://www.tuberadioland.com/myphotos/philco60_x1.gif]

and

[Image: http://www.tuberadioland.com/myphotos/philco60_x2.gif]

The chassis is that of a model 60, though the actual model number is obliterated from the chassis sticker. What's interesting however is that although the cabinet is the style of the later 60 http://www.philcoradio.com/gallery/1935a.htm#ad (with hex knobs and plastic escutcheon), this has the rosette knobs and metal escutcheon of the earlier style http://radioatticarchives.com/images/p/P..._Scott.jpg

It certainly doesn't look tampered with, but you never know. Any thoughts on this one?

The cabinet certainly needs work and I do plan to restore it. However, if I end up never getting around to it, it was certainly worth the $17 I gave for it, even if just for the knobs alone.

Paul

Edit: OK. So I should have fully read the blurb accompanying the photo of the 1935 model 60 in Ron's gallery. I see now that it clearly states that early 1935 model 60s did indeed use the brass escutcheon and I'm assuming the rosette knobs too, just like the previous season's model.

Paul
#2

Hi Paul

Great deal on that cathedral...you're right, it does need a bit of cabinet work but I'm sure you can handle that, eh! Icon_biggrin

It really should have hex knobs. I've seen a few of these out "in the field," so to speak, with the brass escutcheon; but they all had hex knobs. Fellow Phorum member ed857 has one, and it also has hex knobs.

I see yours also has a piece of cloth from a 1932-34 Philco console, instead of the "diamond" pattern normally used in these sets. Perhaps someone has been in it before?

Nevertheless, you did really well, and I'm sure it will turn out really nice.

--
Ron Ramirez
Ferdinand IN
#3

The Model 60 enjoyed a long production life with many production runs and changes from 1934 through 1936.
#4

Paul,

That is a great deal for $17, no question! Keep us posted on it's progress. That one has a lot of potential.

Bill

Sent from my Pentium II on the AT&T Dial Network




Users browsing this thread:
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>