Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Checking XXL tubes
#1

I have 7 XXL tubes, and all but 1 check bad, the one had no filament, so I know it’s bad. But all the others check bad on my Jackson 648s. Some of my other tubes check goo, but not the XXL tubes, but they all check at 30 and 40. Is this normal?

Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
#2

On my 41-300 both of the xxl's were weak/unusable. Poor performance @ the low end of the bcb.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Hi Nortonz!

A Jackson 648 is an emission style tester, so if those tubes don't pass the emission test on the 648, they are probably bad.  However, the best way to know for SURE is to put them in a working radio and compare the performance of the radio.  Both R.L. Drake and Collins radio suggested that method to be SURE that the tube was indeed bad.  I wouldn't pitch the XXL's until I had a working set to plug them in to, so as to make a definite determination.  BTW, if memory serves, an XXL is the same as a 7A4.  But that is the only other sub for an XXL.

Kim Herron W8ZV
w8zv at goldenradioservice.com
1-616-677-3706
#4

That’s my plan, I have three 37’s on order, when they com in for my 41-295, I will try them to know for sure. BTW your memory serves you well the 7A4 is the only sub for a XXL.

Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.




Users browsing this thread:
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX.  They also had a 38-7T (table), and 38-7CS (chairside).  A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

[-]
Who's Online
There are currently no members online.

>