1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Can I use a rooftop TV antenna with my Philco radio?
Jimy
Junior Member
**
Posts: 20
Threads: 7
Joined: Jan 2011
#1

01-19-2011, 11:31 AM
Could I splice into an existing outside roof TV antenna and use it as my radio antenna for my 39-31- philco? I presently use the tv antenna for local channels!

Jim
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

01-19-2011, 11:44 AM
New topic created by site admin. This post was not related to the thread where it was originally posted.
--
Ron Ramirez
Ferdinand IN
Find
audin
Junior Member
**
Posts: 31
Threads: 12
Joined: Mar 2008
#3

01-19-2011, 12:20 PM
The TV antenna itself is unlikely to help at all with the frequencies involved. But the downlead from it might help a bit, though it is still not ideal because the downlead is vertical and, these days, is generally coax. Using the shield of the coax as an antenna might be better than nothing?
Find
jepstr67
Junior Member
**
Posts: 20
Threads: 3
Joined: Mar 2010
#4

03-05-2011, 07:37 PM
Yes. the inner wire is shielded, but I've had pretty good luck using the shield as an AM antenna. Simply making contact with the metal connector will connect your radio antenna lead with the coax outer shield.
AM 1530 Riverside Radio (my home AMT3000 station)
Find
Jimy
Junior Member
**
Posts: 20
Threads: 7
Joined: Jan 2011
#5

03-06-2011, 05:31 PM
Thanks for the info Jepstro, I will give it a shot once I get the chassis repaired!!

Jim!
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration