Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Radio Identification
#1

Hi all,
I am trying to find any info on this philco radio. I have trolled the I'net and the Philco gallery but no joy.
It has an Airzone 6DWS chassis ( I'm in Australia ) and am lead to believe that may have been made under licence here.
Any help greatly appreciated. Oh and is supposed to painted / lacquered dark in areas.
Cheers, Geoff.


Attached Files Image(s)
   
#2

Hi Geoff and welcome,
Unfortunately it doesn't seem to bear any resemblance to the US Philco sets. But the good news is that there are a couple of other forums to inquire with. I would try here   https://antiqueradios.com/forums/viewfor...c6ddc99c69  and  https://vintage-radio.net/forum/index.php

Best of luck with your project!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Thanks for your help Roadioroslyn I will give them a try. Cheers.
#4

https://www.radiomuseum.org/dsp_treffer....rt=&Page=1

Try this site.

Jim
Spring Lake MI
#5

Thank all,
Will try those sites .




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
philco predicta
The model is the holiday without UHF It has no sound and I don't have an oscilloscope or signal generator.cgl18 — 08:51 PM
Philco model 38 code 121 not receiving signal.
I will definitely check my lead length and wire dressing. Thanks for the ideas.Stormlord5500 — 08:06 PM
Philco model 38 code 121 not receiving signal.
Do make sure that you twist the 3 wires from the chassis to the transformer, and dress away from tubes, especially audio...MrFixr55 — 07:38 PM
Philco model 38 code 121 not receiving signal.
The cone unfortunately got damaged when I removed it. The glue that held the cone to the basket was sloppily applied and...Stormlord5500 — 07:12 PM
Philco model 38 code 121 not receiving signal.
So what was wrong with the original speaker? Was the cone damaged? Unless it's totally hopeless I would put it aside as ...Arran — 05:31 PM
My collection presentation
There is an article on my site that introduces the first portable radios in my collection. I have only provided a link t...Vlad95 — 01:17 PM
Electrolytic restuffing/internals
Bridkarl This specific cap you have is the easiset type to restuff. I usually cut it at the upper border of the depr...morzh — 11:35 AM
philco predicta
Hi CGL18, First off, welcome to the Philco Phorum. I have not worked on a TV for a while but here are some givens: ...MrFixr55 — 08:22 AM
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM

[-]
Who's Online
There are currently no members online.

>