Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

IDENTIFICATION PT50 or TH14 ??
#1

Hi, I am new on this forum!
Found recently this one, very poor condition.
Probably PHILCO PT50 Transitone (1940) or may be TH14.(seems same line up)
If PT 50, rear coil waxed for "tropicalisation" ? and why these turns in both directions
perpendicular ?
Someone could give precisions please ?

And for building new cabinet, I am looking for a good photo of the box.

Thanks for help.
megawave
French collector

[Image: http://img638.imageshack.us/img638/9291/...50face.jpg]

[Image: http://img339.imageshack.us/img339/702/philcodessus.jpg]

[Image: http://img836.imageshack.us/img836/1585/...bottom.jpg]

[Image: http://img407.imageshack.us/img407/1162/...tcopie.jpg]
#2

Looking at the service bulletins for both 1940 models, the schematics are the same (except for one additional cap in the TH-14. The other components have slightly different values as well, but schematic is virtually identical.
Tube complements are also the same.
The big differences are dial plates, and wood (TH-14) or bakelite (PT-50) cabinets.

So, it appears you have a chassis out of a TH-14 or TH-16, due to he dial face.

Chuck
#3

Hi Chuck, thank you for infos; I have a picture of PT50, (found on Ron's site, see below) but it is WOOD cabinet. Do you know what was the look of bakelite cabinet for this one ?
Thanks
megawave
Icon_smile
French collector


[Image: http://img703.imageshack.us/img703/3645/...50wood.jpg]

Uploaded with ImageShack.us
#4

No I don't a picture. I believe it is similar to the PT-47/PT-51, but with out the pushbuttons.

Ron can correct me here if I'm wrong.

Chuck
#5

OK Chuck, thanks for reply, all is clear now. (Seen also your reply on Antique radio forum.)
Photos on line when job finished. Icon_smile
Sincerely,
megawave
French collector
#6

Hello Megawave,

Just so happens I have a PT-50 cabinet. Icon_smile If you need detailed photographs and dimensions, please contact me.

I agree with Chuck that you have a TH-14 or TH-16 chassis, due to the design of the dial face.

Just for fun, here's what they look like.

TH14: http://www.philcoradio.com/gallery/1939c.htm#m

TH16: http://www.philcoradio.com/gallery/1940a.htm#bn

I find it interesting that the TH-14 was advertised as a (January) 1939 model, yet it is not in the 1939 Philco RMS Yearbook - it is in the 1940 RMS Yearbook. Icon_confused: Icon_confused

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Electrolytic restuffing/internals
I don’t have a vise so I had to hold it in my hand. Not optimal but covered up by the hvac tape in the end. I have a few...bridkarl — 11:52 PM
Electrolytic restuffing/internals
Bridkarl A question. For a hacksaw the cut looks a little...jagged. Why?morzh — 11:45 PM
The list of my radio & TV collection!
As usual, an interesting post from you, Peter. This seems to be similar to the RCA 3-BX-671 and the Zenith Transoceanic...MrFixr55 — 11:41 PM
The list of my radio & TV collection!
Hello Peter, Thank you for sharing your new video and looks like your weather is nice their too. it was like 25 Cel...radiorich — 11:05 PM
Electrolytic restuffing/internals
hello bridkarl, I will post some better photos ! Sincerely Richardradiorich — 10:14 PM
Electrolytic restuffing/internals
I just taped the two pieces of the cap together, but I can see your method is better. I just held the lead in with solde...bridkarl — 08:18 PM
Electrolytic restuffing/internals
hello bridkarl, Well done ! Here is a Photo of the base of Philco capacitor that I cut open you can see how I glued th...radiorich — 08:14 PM
philco predicta
Hi CGL18, Here is a link for the schematic from the Early television Foundation: WARNING!! One side of the Chassis i...MrFixr55 — 08:09 PM
The list of my radio & TV collection!
Peter; I like Canadian General Electric sets, whilst the model numbers are often the same as their U.S General Electr...Arran — 05:44 PM
Electrolytic restuffing/internals
Did as suggested. Cut can with hacksaw, removed internals, attached new 8mf cap - with ample use of cardboard and elec...bridkarl — 03:36 PM

[-]
Who's Online
There are currently no members online.

>