Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Sonora RBU-175 Low Band Issues
#1

Hello Fellow Radio Heads. I have ventured from the world of Philcos to try and expand my knowledge of all radios in general. I have a Sonora RBU-175 that I have re-capped all but the bigger filter caps. The radio appears to be aligned just fine as any station above 950 comes in good and loud and appears to be dead on accurate. My issue is as soon as I go below 950, I seem to loose any type of reception. I get absolutely no type of sound......nothing. Is there a definitive line between upper and lower bands that I may be able to Isolate maybe a loose connection, Bad resistor or at this point.....ANYTHING, LOL. Thanks in advance for any help you can provide.

Jerry Gatewood
Philco 41-280 (121)
#2

Likely problem is that the plates of the tuning cap are shorting as the capacitor is meshed.
#3

You are a freaking Genesis. I have been sitting in front of this thing for 6 hours and I wound it down all the way and sure enough, I found a bent fin. Straightened it out and Bingo, Got tone all the way down. THANK YOU!!!!!!!!!!!!!!!!!!!!!!!!

Jerry Gatewood
Philco 41-280 (121)




Users browsing this thread:
[-]
Recent Posts
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum, Martin! Open a new thread in Philco Electronic Restoration when you begin working on your 38-7. ...GarySP — 08:28 PM

[-]
Who's Online
There are currently 985 online users. [Complete List]
» 1 Member(s) | 984 Guest(s)
Avatar

>