Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Replacement for .7 to 1 interstage transformer
#1

Had a similar thread, but it wasn’t as specific as this, and therefore got lost. Anyone know a good replacement for this interstage transformer? Has a turns ratio of .7 to 1. It’s in a Sparton 28.

[Image: https://i.imgur.com/lNO85AP.jpg]
#2

It can not be .7 to 1.
Just by the sheer DC resistance, even if accounted for the wire gauge, 700 Ohm to 1 Ohm means huge difference in the number of turns.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Morzh,

Look at the schematic. Primary at 3580Ω, secondary center-tapped at 2985Ω (or 5970Ω total secondary). equals a turns ratio of actually .599 to one, but close enough to the rated value of .7 to 1. Am I missing something here?
#4

Morzh,

Oh, I see. Your're looking at the output transformer. I'm referring to the input or interstage transformer.
#5

Oh..yes I was looking at the output.

38-116 has a similar one.
Lets' see if Tubes and More has something.
Nope. They have 1:2 and 1:3. Can't see that ratio around.
Maybe someone else can.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

I found a 1:1.5 but that was the lowest. Did find a 1:1 but was discontinued.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#7

1:1.5 and 0.7 to 1 are close enough.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#8

It's a Hammond 124D

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#9

Great! Thanks Terry. I'll get a 124D and give it a shot.

Pat




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
The list of my radio & TV collection!
A little light Saturday positive about our hobby in our feed... My new every Saturday video about antique radio equipme...RadioSvit — 02:12 PM
Model 70 Cabinet Trim
musar , Well if you have any more questions feel free to post away . Sincerely Richardradiorich — 08:56 PM
Model 70 Cabinet Trim
Although I have not made any cabinets or cabinet parts for a couple of years, I still have some parts left over, includi...Steve Davis — 06:26 PM
philcorepairbench.com - shadow-meter
Thanks Ron. But I can't find those articles.fenbach — 02:43 PM
Model 70 Cabinet Trim
Thank you, Gary. Before making my original post, I had clicked on "Steve Davis Cabinets" only to find that it...musar — 02:25 PM
philco predicta
Welcome to the Phorum, cgl18! I am not your resource for television repair, but lots of friendly help is available here...GarySP — 02:12 PM
Model 70 Cabinet Trim
Welcome to the Phorum, musar! You can send Steve Davis a private message (PM). The site is at the top of the Home page...GarySP — 02:09 PM
Model 70 Cabinet Trim
How do I contact him? The only contact information for him I could find when searching online was a telephone number th...musar — 10:38 AM
philco predicta
Hello, good afternoon, I would like to ask what the possible problem could be if I don't have an image on the screen. I ...cgl18 — 10:19 AM
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM

[-]
Who's Online
There are currently 859 online users. [Complete List]
» 1 Member(s) | 858 Guest(s)
Avatar

>