Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Anyone see what's wrong with this aircap?
#1

Philco 70. Zoom in.


Attached Files Image(s)
   
#2

At first glance, a problem is not obvious to me! (Other than the warped dial. But that's not really the air cap.) Give me a clue!
#3

Not necessarily the cap itself, the unit as a whole and of what it contains.
#4

Hmmm. It looks like a lot of "staining", perhaps because of mouse urine, but that is pretty typical!
#5

The leftmost trimmer cap has most of the top plate missing....if this is it.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

Well, I may be wrong, but page 16 of the 1937 Philco List Parts catalog on this site says the bulb bead should be white, indicating a 2.5 volt bulb, not a blue 6.8 volt bulb. The bulb voltage is taken right off the heater 2.5 ac line; I always thought it looked dimmer than it should be - and tried cleaning the socket to no avail.
#7

Then your thread name is a bit misleading as the bulb is not a part of the cap. It jis mounted on the dial assembly which is then attached to it, but the cap ends where there is no longer stator, rotor, trimmer or the shaft.
There is then nothing really wrong with the cap.
The bulb...???

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#8

The air cap not on the radio chassis?!  Icon_eek Icon_lol Icon_twisted




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
philco predicta
The model is the holiday without UHF It has no sound and I don't have an oscilloscope or signal generator.cgl18 — 08:51 PM
Philco model 38 code 121 not receiving signal.
I will definitely check my lead length and wire dressing. Thanks for the ideas.Stormlord5500 — 08:06 PM
Philco model 38 code 121 not receiving signal.
Do make sure that you twist the 3 wires from the chassis to the transformer, and dress away from tubes, especially audio...MrFixr55 — 07:38 PM
Philco model 38 code 121 not receiving signal.
The cone unfortunately got damaged when I removed it. The glue that held the cone to the basket was sloppily applied and...Stormlord5500 — 07:12 PM
Philco model 38 code 121 not receiving signal.
So what was wrong with the original speaker? Was the cone damaged? Unless it's totally hopeless I would put it aside as ...Arran — 05:31 PM
My collection presentation
There is an article on my site that introduces the first portable radios in my collection. I have only provided a link t...Vlad95 — 01:17 PM
Electrolytic restuffing/internals
Bridkarl This specific cap you have is the easiset type to restuff. I usually cut it at the upper border of the depr...morzh — 11:35 AM
philco predicta
Hi CGL18, First off, welcome to the Philco Phorum. I have not worked on a TV for a while but here are some givens: ...MrFixr55 — 08:22 AM
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM

[-]
Who's Online
There are currently 1057 online users. [Complete List]
» 1 Member(s) | 1056 Guest(s)
Avatar

>