Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Circuit diagram- Philco S521B Radio
#1
Smile 

Hello, I'm new here.
I have a Philco Empire Automatic S521B Radio of GB (1938). I'd like to reactivate it, but I can't find on the internet a circuit diagram for this model. I have found a circuit diagram for Philco D521B but it isn't the same diagram which I need. I've attached photos of my radio. Is somebody able to help me?                    
#2

Hope this info is helpful. Welcome to the Phorum.   https://www.radiomuseum.org/r/philco_emp...521_b.html
#3

Hi and welcome,
Give this one a try:  https://www.radio-workshop.co.uk/service...20D521.pdf

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

The OP has stated that a D521 schematic is not the same as an S.521B schematic.

malkmm - I found a Philco (UK) Service Bulletin for model S.521. It may, or may not, be the same as an S.521B but maybe it will help? I will send you a private message (PM) on this subject.

--
Ron Ramirez
Ferdinand IN
#5

Welcome to the Phorum!
#6

It looks like the S521B might be a battery set, though it's also possible that someone may have swapped in an A.C chassis into the cabinet of the battery set.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
philco predicta
The model is the holiday without UHF It has no sound and I don't have an oscilloscope or signal generator.cgl18 — 08:51 PM
Philco model 38 code 121 not receiving signal.
I will definitely check my lead length and wire dressing. Thanks for the ideas.Stormlord5500 — 08:06 PM
Philco model 38 code 121 not receiving signal.
Do make sure that you twist the 3 wires from the chassis to the transformer, and dress away from tubes, especially audio...MrFixr55 — 07:38 PM
Philco model 38 code 121 not receiving signal.
The cone unfortunately got damaged when I removed it. The glue that held the cone to the basket was sloppily applied and...Stormlord5500 — 07:12 PM
Philco model 38 code 121 not receiving signal.
So what was wrong with the original speaker? Was the cone damaged? Unless it's totally hopeless I would put it aside as ...Arran — 05:31 PM
My collection presentation
There is an article on my site that introduces the first portable radios in my collection. I have only provided a link t...Vlad95 — 01:17 PM
Electrolytic restuffing/internals
Bridkarl This specific cap you have is the easiset type to restuff. I usually cut it at the upper border of the depr...morzh — 11:35 AM
philco predicta
Hi CGL18, First off, welcome to the Philco Phorum. I have not worked on a TV for a while but here are some givens: ...MrFixr55 — 08:22 AM
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM

[-]
Who's Online
There are currently no members online.

>