Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

I picked up this Opus 6 yesterday
#1

Talk about a sweet sounding radio.  Wow this thing sounds good. Superb reception as well.  Best I've had at my place where many of my other radios have trouble The cabinet is in excellent condition as are the glass knobs and buttons. 6 speakers, all working.  I've been on the hunt for a nice one for a long time. My search is done.


Attached Files Image(s)
       
#2

Them Germans built nice ones in 50s, yes. Any Telefunken is an excellent radio.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Just found one of these, will start restoring it soon. It is very nice condition but would like to recap it.

Jim
Spring Lake MI
#4

Jim please take lots of pics to share. David
#5

Will do.

Jim
Spring Lake MI
#6

At the very least I would want to replace the audio coupling capacitors, the tone correction cap on the primary of the output transformer (if it can one) and any bypass that runs between B+ and ground. A lot of West German radios used ERO brand capacitors, they are to German sets what Hunts are to British ones, replace on sight.
Regards
Arran
#7

Thank you Arran.
When I get started on this I will start a new thread.

Jim
Spring Lake MI
#8

Yes, my Grundig used ERO.....the worst I've seen so far. I keep them just so I could demonstrate how bad cap could drift. Up to 4 times up.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#9

Some tube-type and early solid-state Fishers also use ERO caps. The consensus seems to be divided on these as to replace vs. keep.

I replace them.

--
Ron Ramirez
Ferdinand IN
#10

Ron

when a cap goes up in value 4 times, to me there is no valid justification for leaving it in.
Out of all ERO caps in my radio (about 30+) there is no one single cap that did not go up at least 3x the value.
I think I might've even put a picture in my Grundig thread.
For comparison, all American caps in Philcos or Zeniths were 1.5x to 2x the value and in fact did work. Still needed to be replaced.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#11

No argument from me. Like I said...I replace them.

--
Ron Ramirez
Ferdinand IN
#12

https://philcoradio.com/phorum/showthrea...606&page=2

Actually, on this page I have the picture of 0.033uF cap measuring exactly 0.33uF.

Times 10.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#13

I was addressing the original poster in this, the set might work now, but it may not work a week from now, but replacing the audio coupling caps is the bare minimum someone should do.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM

[-]
Who's Online
There are currently 376 online users. [Complete List]
» 3 Member(s) | 373 Guest(s)
AvatarAvatarAvatar

>