Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

General Electric Trimline 600
#1

I bought one of these at the Memorial Day Flea Market at Hartville marketplace today. I have it playing, but anyone here know how the heck you get into the controls to clean them? I took the back off and all the electronics are jammed in on one side with no obvious way to slide them out or access them. I was able to get to the band switch through the vents on the bottom, but that's it. It needs the rest of the controls cleaned and new dial lights. Man, this thing is HEAVY!

No matter where you go, there you are.
#2

Got it figured out after looking the stereo over again with a fresh set of batteries in my flashlight. Had to remove the knobs, then found that the screws were hiding behind the dial bezel after I found out how to pop it off. Everything in there is black, so was hard to tell what I was looking at from the rear until I finally saw the ends of the screws.

No matter where you go, there you are.
#3

Got a photo?

Paul

Tubetalk1
#4

Here's a quick picture after replacing the dial lights and bringing it into the house to play for a bit. I swear, FM has been sounding like crap on all my radios this evening and is only a bit better now. Anyways, here is the General Electric Deluxe Trimline 600:

   

I still need to attach the the two metal grills to the back of the speakers again as the double-sided adhesive tape GE used has given up, then it's on to the changer and perhaps a capacitor or two in the future.

No matter where you go, there you are.
#5

Hmmm - Deluxe Trimline. Isn't that an oxymoron?
#6

So is calling it portable. Lug-able might be a better term. It definitely still needs work though. The stereo FM isn't working, at least I can't hear any difference switching between mono and stereo FM settings. Also after about 10 minutes the FM gets somewhat distorted and the dial cord slips at the center of the dial. So, back to the $5 RCA SS3000 for vintage stereo listening. That thing has been a reliable workhorse since I cleaned it up and it's from the same year range as the GE. Seems odd the thing I bought cheap on a whim works better than the GE which I had been looking for and bought for $25. Still wish I could find the Zenith tube stereo portable.

No matter where you go, there you are.
#7

Just a marketing ploy, put a handle on it and call it portable.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM

[-]
Who's Online
There are currently 2367 online users. [Complete List]
» 1 Member(s) | 2366 Guest(s)
Avatar

>