Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Stromberg-Carlson model 130R
#1

I just finished up the chassis on this set and did an alignment as shown in the service information below:

http://www.nostalgiaair.org/pagesbymodel...021331.pdf


The radio plays great and the dial is right where it should be on the A band or broadcast....except I cannot get the local station which is at 1470 kc to come in! Everything else is where it should be. I did the alignment procedure several times just to be sure and each time had the same results.

BUT....

1470 comes in loud and clear at the beginning of the B band!

I think because the two bands overlap (A covers 540 to 1500 kc, and B or the police band covers 1450 to 3500 kc), the very high end of the broadcast band comes through on the police band!

This is the only radio I have with that phenomenon.

Greg V.
West Bend, WI
Member WARCI.org
#2

Set your band switch to a A dial to 1470kc and find where your local osc is. Should be at 1935kc. If not align osc trimmer to put it there.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Finally was able to find it on the AM band Icon_thumbup

Greg V.
West Bend, WI
Member WARCI.org




Users browsing this thread:
[-]
Recent Posts
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM

[-]
Who's Online
There are currently no members online.

>