Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Oscillator Coil 32-1311
#1

I was troubleshooting a 37-84 and found that the oscillator coil is open. The Philco part number is 32-1311. Here are my questions:

1. Is there any other Philco oscillator coil that would be an acceptable substitute? If so, do you have the Philco part number? (Maybe I can get lucky and find one at Play Things of the Past).

2. Is there any oscillator coil currently stocked by AES or Radio Daze that would be an acceptable? The IF is 470 kHz, not 455.

Thanks for your help!

Joe Connor
#2

I had this same problem on my 37-84. If it's the primary that's open, you're in luck.

Your best bet would be to rewind the primary yourself. It's not as difficult as you might believe. It's only a handful of turns (don't remember how many offhand), but the easiest thing you could do would be to unwind the primary and count the turns. Use some very light magnet wire to replace it and wind the new wire back on. An alternate fix would be to unwind the coil until you find the break, repair it, and wind it back on (considering the low number of turns, it might not be the best solution). When done, seal the coil back up with fingernail polish or some other similar solution.

If the secondary is open, that might be a tougher situation. For that I yield to Mr. Philco and/or Chuck, who can supply more specifics on the subject, since they're the experts. Icon_smile

IIRC, I used magnet wire I got at Radio Shack, and it worked fine. Good luck!

Bill

Sent from my Pentium II on the AT&T Dial Network




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
That looks a lot like an aircraft connector of some kind, even if it's a U.S.N power supply. I have a book somewhere abo...Arran — 02:56 AM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
hello david, I have a similar generator in my collection that features a cast iron, single-cylinder Briggs & Stratt...radiorich — 01:00 AM
under chassis parts locator diagram for 1938 Zenith 9s262
Has anyone gone to the trouble of creating an under chassis parts locator image?  Yes, I can identify components by foll...bobloney — 08:57 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Try looking at this site the book mark is for a old generator that I was given. David    https://radionerds.com/index.ph...David — 08:36 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Hello Everyone, I am looking for voltage identification for all the pin positions on the socket of a CRV-20130 power su...Tonym4704 — 08:16 PM
Philco P45-6365 Universal Transformer Instruction Manual
Can anyone guide me to where this may be found?GRG — 03:00 PM
54C Complete Teardown/Rebuild
I don't think that I have encountered a 12Z3 before, curious how it uses one of those but includes a #43, which is a 25 ...Arran — 02:17 PM
HiFi (Chifi) tube amp build - but my own design.
It's the other forum. I'm also in DIY, but mostly read there. Honestly, I kinda jumped into this without much thought to...TV MAN — 10:43 AM
Philco 71 Code 125
Hello,  I am in need of a schematic for this radio. Mine has the three separate circular tube shields and a shadow me...dconant — 08:06 AM
Stromberg Carlson 1500 Squeal
And life just keeps getting more complicated.dconant — 07:57 AM

[-]
Who's Online
There are currently no members online.

>