Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

A-361 radio
#1
Sad 

I had sent out my husband's A-361 radio  for repair and have since learned that the glass tuning dial was mistakenly discarded.  If anyone knows of where I might get another one, I would be very grateful.  I can't say how disheartening this is.
Thank you,
Martha
#2

There is a A-361 on Craigslist in Onalaska Wisconsin for 50 bucks. You could always inquire if they want to part it out. Good luck
Jim
#3

Three possibilities that I can think of for you.
1) Put a Wanted Ad in the Phorum Wanted Ad section. Its not likely but possible that someone has one in their boxes of miscellaneous repair parts.
2) Watch Ebay for sales of A361 radios for a donor dial glass.
3) You can contact the folks at RadioDaze and talk to them about custom making a dial glass for you. https://www.radiodaze.com/contact/
That may require you to have a dial glass on loan for them to copy but I'm not sure about that. I have purchased dial glass from them but they were not custom made for me.

Other folks may have some other ideas for you. Good luck.
#4

Thank you for the suggestions! I so appreciate the knowledge and support on the Phorum. I will try them out!
Warm regards,
Martha




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>