1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
40-216 SW antenna compensating condenser
rjm
Member
***
Posts: 70
Threads: 17
Joined: Jan 2006
City: Newbern State, Province, Country: Tennessee
#1

11-15-2022, 05:12 PM
My compensating condenser on the SW antenna broke. Would anyone know the value. Listed in the schematics as part # 31-6326. None of my parts books I have show it. I have tried what I have a 40-240pf and a 110-580pf. Can't dial in to a strong signal from my signal generator. Cuts it or makes it weak. If I disconnect the internal antenna and run a wire, it picks up the generator strong at 18mc, adjustment frequency.
any help would be appreciated.

Thanks,
        Richard
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
#2

11-15-2022, 05:31 PM
At 18mc you are not going to need much capacitance. I would start w/20mmf and go down if necessary.

GL
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
rjm
Member
***
Posts: 70
Threads: 17
Joined: Jan 2006
City: Newbern State, Province, Country: Tennessee
#3

11-15-2022, 06:07 PM
cool thanks. I can get a 2-70pf. Should give me the range.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Electrolytic restuffing/internals
I just taped the two pieces of the cap together, but I can see your method is better. I just held the lead in with solde...bridkarl — 08:18 PM
Electrolytic restuffing/internals
hello bridkarl, Well done ! Here is a Photo of the base of Philco capacitor that I cut open you can see how I glued th...radiorich — 08:14 PM
philco predicta
Hi CGL18, Here is a link for the schematic from the Early television Foundation: WARNING!! One side of the Chassis i...MrFixr55 — 08:09 PM
The list of my radio & TV collection!
Peter; I like Canadian General Electric sets, whilst the model numbers are often the same as their U.S General Electr...Arran — 05:44 PM
Electrolytic restuffing/internals
Did as suggested. Cut can with hacksaw, removed internals, attached new 8mf cap - with ample use of cardboard and elec...bridkarl — 03:36 PM
The list of my radio & TV collection!
For fans of antique radio... My new video... How to test radio tubes on a Hickok 530B tube tester? Test radio tubes o...RadioSvit — 01:25 PM
philcorepairbench.com - shadow-meter
Thank you Billpoulsbobill — 11:53 AM
philcorepairbench.com - shadow-meter
Hi, Try here Philco Service Hints & Tips, Number 1 It's from the web archive (Way Back Machine).Keith — 10:17 AM
PT-6 finished!!
Hi Arran,  Yes, you are correct, the "nominal" voltage for these Loctal tubes was the same 6.3 or 12.6 V as...MrFixr55 — 07:48 AM
PT-6 finished!!
Actually the Loctal tube series, with number beginning with "14" are 12.6 volt tubes, at 150 ma, I'm not sure ...Arran — 02:14 AM

[-]
Who's Online
There are currently 1086 online users. [Complete List]
» 4 Member(s) | 1082 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration