1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Removing big paint lumps
bridkarl
Member
***
Posts: 197
Threads: 43
Joined: May 2023
City: Pocatello State, Province, Country: idaho
#1

02-25-2024, 01:39 AM
Someone has dropped a huge lump of paint on this metal case. Any thoughts on how to soften this up for removal? Usually I start with WD-40 or goo-be-gone but this looks like I’d need to file it off. Not a Philco, but this seemed the best place to put this question.


Attached Files Image(s)
   
Find
Arran
Phorum Expert
*****
Posts: 4,894
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
#2

02-25-2024, 03:14 PM
It looks more like tar splashed on it, or maybe wax? It may melt off with a bit of heat but mineral spirits should work as well.
Find
GarySP
Super Moderator
******
Posts: 2,159
Threads: 158
Joined: Jan 2013
City: Westland, MI
#3

02-25-2024, 08:19 PM
I'd try heating it with a heat gun slowly to soften the mass, then carefully scrape it with a putty knife. Are you repainting the entire cabinet? Take care and BE HEALTHY! Gary
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Find
slford310
Member
***
Posts: 115
Threads: 26
Joined: Jul 2022
City: Monticello State, Province, Country: Illinois
#4

03-02-2024, 08:31 PM
Kind of reminds me of a big blob of solder that splashed on it.  
Philco's: 86 Lowboy 90 Highboy 95 Highboy 76 Highboy 112X Console 118X Console 41-265 Console 41-608P Console 52GC 370 LZ 512 20 Baby Grand 70 Baby Grand 71B 52B 118B 60B 84B 610B 37-89B 38-10T 38-35B 41-221CI 42-321T 46-1203 48-214 48-206 49-506
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2306 online users. [Complete List]
» 3 Member(s) | 2303 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration