Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

41-295 REFINISHING
#1

I'm going to refinish my 41-295 , but before I start to strip it, does anyone know if Philco cabinets used the "PHOTO FINISH" like Zenith did ? ,It looks like they didn't but not 100% sure Icon_confused:
#2

Hi Bill,
I don't beleive that set had Photo finish. Posting a picture of the area you think is PP we should be able to tell for sure.
Another way is to take a high power magnifier and look for the 'dots' that are usually seen on the PP areas.

I have a set in the basement I think is the same (I can't turn it right now around to check) But it does have inlaid wood strips in the front side pieces, and below the dial escutcheon.

There is a picture of a cabinet under restoration, and I did not see anything that looked like PP on that cabinet.
Philco did use photo finish on many sets, so it is best to check first.

Gary.
#3

THANK YOU , Ihave so Zeniths with the photo finish ,what can be done for them? ,BILL
#4

Here's a link from Ron's site about photo finishes. Hope it helps.

http://www.philcoradio.com/schooley/index.htm

Bill

Sent from my Pentium II on the AT&T Dial Network




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM

[-]
Who's Online
There are currently 1843 online users. [Complete List]
» 1 Member(s) | 1842 Guest(s)
Avatar

>