1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 610B Tone Control 30-4318 caps
Ken Kidd
Junior Member
**
Posts: 16
Threads: 6
Joined: Apr 2011
City: Morgantown WV
#1

10-12-2011, 11:26 AM
Hi all, Have some conflicting info on the cap values for this tone control. Both my Philco schematics(one early and one later production) list .01 and .02. I have Ray's original "Philco Condensers and More" ( Great resource book!!!) which lists a .02 and a .003 for this tone control. The Philco Repair Bench does not list this tone control. Does anyone know which would be the correct ones? I'm assuming the .02 value is correct. Thanks-Ken
Find
Texasrocker
Phorum Expert
*****
Posts: 909
Threads: 117
Joined: Jun 2007
#2

10-12-2011, 02:37 PM
Those caps aren't that critical, either combination will work. Use what you have, just follow correct layout (placement). Yes, the Philco Condensers and More book is nice to have!! Best of luck with your restoration.
Find
Ken Kidd
Junior Member
**
Posts: 16
Threads: 6
Joined: Apr 2011
City: Morgantown WV
#3

10-12-2011, 02:56 PM
Thanks for the input. Will probably go with whats listed in the Philco schematic-Ken
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
#4

10-12-2011, 09:01 PM
Go with to .003 and .02. That will give you a fair amount of difference between the two setting.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#5

10-12-2011, 11:01 PM
Yes, agree with Terry, .003 and .02 are a good combination for steps in tone.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration