Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Grill cloth on Philco 60-121
#1

Hello Friends.

I need your help.

I am restoring a Philco 60-121.
The grill cloth is not in good conditions, and i would like to remove and put other new in good conditions, but i do not know where i can find this grill cloth.

I see in AES, Radio daze and http://www.grillecloth.com/ , but i do not see this grille cloth to my radio.

In the next images you can see this grill cloth.
[Image: http://img422.imageshack.us/img422/5894/...ah0.th.jpg]

[Image: http://img161.imageshack.us/img161/396/1...eb3.th.jpg]

[Image: http://img48.imageshack.us/img48/5659/10...oo7.th.jpg]

Thanks for all.
#2

Hi Jose,

While not an exact match, ( http://www.grillecloth.com/ ) #2 or #24 should work fine. I like to soak the cloth in some coffee for a minute or two before installing (letting it dry first of coarse). That will take some of the "shine" off of the new cloth and it wont stick out like new cloth. Should be a nice looking radio when your done.

good luck,
jerry.
#3

Hello Jerry.
Thanks for the information.

But can you send me the link whith the #2 and #24? I do not see those numbers in the address http://www.grillecloth.com/

Thanks
Jose Antonio
#4

Hi Jose,
Sorry I had a typo in the grillecloth reference,

Heres the page that I was looking at:

http://www.grillecloth.com/pages/p1.html

Take care,
jerry.
#5

Hello Jerry.
Thanks for all.
I can now see this link.

Thanks.
Jose Antonio




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 953 online users. [Complete List]
» 2 Member(s) | 951 Guest(s)
AvatarAvatar

>