Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-160 escutcheon
#1

I have recently acquired a 40-160 but the escutcheon covering the dial and 6 push buttons is missing. Does anyone know where I might possibly get these parts?
#2

jetmech7860 Wrote:I have recently acquired a 40-160 but the escutcheon covering the dial and 6 push buttons is missing. Does anyone know where I might possibly get these parts?

As far as I know the only source for these parts would be a parts set or parts salvaged from a parts set. You should be able to find the pushbuttons, as they are bakelite, but finding a good escutcheon may be a problem. The original escutcheons used on the 40-158, 40-160, and 40-165 consoles were made out of a type of plastic that has a habit of warping and cracking (some say it's Tenite) and as far as I know nobody is reproducing that style of escutcheon. Very likely the only thing you could do is to make a suitable facimile with either sheet brass, or plastic, or possibly wood. This is strange as most of the Philco models from 1940 used some form of brass escutcheon but these sets were the exception, the 1941 and 42 models were just the opposite with most escutcheons being made out of plastic.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>