Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Found a 625 today
#1

Don't know if I paid too much for it but I don't think its in all that bad of condition. One electrolytic was replaced at one time I think, $55

[Image: http://i248.photobucket.com/albums/gg187...012001.jpg]

[Image: http://i248.photobucket.com/albums/gg187...012002.jpg]
#2

I think you did very well indeed for $55. Icon_thumbup

--
Ron Ramirez
Ferdinand IN
#3

Darn good shape! Ya dunn real good.
A rather hard model to come across too.

Icon_thumbup

Chuck
#4

So what is the difference between a 625 chassis and a 620? The wavelengths covered? I noticed that like a 620 it doesn't have a shadowmeter like a 630 would.
Regards
Arran
#5

It doesn't have a power transformer either, it's the AC/DC version of the 620.
Terry
#6

So take the usual isolation transformer
precautions and procedures with this hot-chassis set.

Chuck
#7

This isn't an AC/DC set, it uses a small, low profile power transformer. You can (barely) see the top of it to the left, behind the 80 tube, in Jim's second photo.

Arran, the 620 and 625 cover the same frequencies. There are differences in the circuitry, chiefly in the AVC circuit. The 625 also has a moving shadow mask behind the dial scale, with three holes that allow the greatest illumination only to the band in use.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM

[-]
Who's Online
There are currently no members online.

>