Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Does anyone have any info they could share?
#1

Hi there.

I'm new to the forum so I'm hoping I'm following protocol.

I inherited an old Philco console Radio with a turntable several years ago. The radio was made in the early 50's in Toronto Canada. The model number on the cabinet is 730 which also matches the chassis number on the radio. On the cabinet it says "Model No." and on the metal chassis it says "Chassis No.". Anyhow.. I have searched high and low and cannot find a thing about this unit on the net. I've restored the cabinet but it just won't be right if I can't restore the radio.

I'd appreciate any help you can give me.
#2

Hello and welcome.

I'm afraid I can't help you, since I have very little info on Canadian Philco radios. The Canadian models began to use different model numbers from their US counterparts in 1939, and some Canadian Philcos are quite different than USA models.

So you will need info from someone in Canada, or someone who has Canadian Philco info.

--
Ron Ramirez
Ferdinand IN
#3

There was a post on this forum last year about the same radio:
http://philcoradio.com/phorum/showthread.php?tid=232

Carl
Northern Panhandle, WV
#4

Thanks Carl. Missed that entirely. Icon_redface

--
Ron Ramirez
Ferdinand IN
#5

Thanks a million. Thats the unit! I have a starting place now Icon_biggrin




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 785 online users. [Complete List]
» 1 Member(s) | 784 Guest(s)
Avatar

>