Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Looking for a Clean Schematic for 37-675
#1

delete
#2

You can't beat the large clear copies with all data from Chuck.
Jerry
http://www.philcorepairbench.com/schematics.htm

A friend in need is a pest!  Bill Slee ca 1970.
#3

I'll second that!! Super product, schematic is enlarged and crystal clear!!

Icon_thumbupIcon_thumbup
#4

I only wish I had something to print those nice big schematics with. We don't even have a Kinko's within 50 miles of here.
#5

HA!! And if you did they would probably either pint it in Arabic or sabotage the schematic so your radio would go "BOOM" when you turned it on.

Icon_wink
#6

Why would they print it in Arabic OR sabotage it? The only people I know of in this country that speak Arabic are either tourists or embassy staff in Seoul.
#7

Oh crap, that's right. Dari and Pashto.

But I stand by the statement about sabotage.

When one (read Amercan) can freely walk the streets of ANY town there I will gladly recant.
#8

Seoul?? Thought it was Afghanistan!!!Icon_eh
#9

As the OP has deleted his post, shall we continue the discussion, or just drop it?

I guess he wanted something that was very clear, very easy to read, and free.

--
Ron Ramirez
Ferdinand IN
#10

Well...mine only cost the copying charges and postage, averaged over large and small no. of copies, depending on model.

I usually toss out 3-4 orders that never show, once they don't see anything "happening." Emails ask when did I send them, and I reply that I have not seen any payment. Never hear from them again.

Others think something pops up on my site to d/l or I don't know what.

Oh, any no one reads the first paragraph on my site with all the details, cost, etc either. I'm constantly being asked "How much?".

Also when a customer places an order and it generates a email to me, there is a FUL PAGE that pops up with my mailing address that stays there unless you click away from it. Most people, again, don't read it and then I get "Where do I send check?" emails.

Like they always said, You can lead a horse to water . . . . . .

Chuck
#11

Read? You mean you actually expect the shmendriks out there who barely know how to turn a computer on to actually read anything??? Icon_rolleyes

All they want to see are the pretty pictures, after all. They are oblivious to any text...or so it seems.

Chuck, believe me, I know how you feel...A virtual cold one for you on the house. Icon_biggrin

--
Ron Ramirez
Ferdinand IN
#12

Thanks - three fingers, one cube.....leave the bottle......




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum, Martin! Open a new thread in Philco Electronic Restoration when you begin working on your 38-7. ...GarySP — 08:28 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum! :wave: Here's the schematic for that radio from our digital library: Something to do bef...klondike98 — 08:05 PM
Philco Model 38-7: what caps & resistors do fail typically?
Hi all, on vacation in Montreal,  a friend of mine showed me a Philco Model 38-7 console radio from the 30ies. Mechan...Musaeum — 07:21 PM
Part numbers to model cross
I looked thru the documents and did not see one. Might have missed it though.Jim Dutridge — 07:16 PM
Philco 42-345 Restoration/Repair
Please tell me this was it, I replaced resistor 27 and it's playing on the broadcast band. I am afraid to change the ban...osanders0311 — 06:12 PM

[-]
Who's Online
There are currently 1128 online users. [Complete List]
» 3 Member(s) | 1125 Guest(s)
AvatarAvatarAvatar

>