Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Beam of Light
#1

Does anyone have a Beam of light record player? I have one but near as I can tell it is missing a part the controls or sets the turntable speed. If you have one could you take a closeup picture of the end where the governor is? Mine has a hole in the bracket and it looks like there should be something there to hold the end of the governor.
Other than the speed problem I have it playing good.
Thanks for any help you can provide.

Gregb
#2

hey Greg
what model do you have
sam
#3

The radio is a 41-608, I would have to look to see if there is a model number on the record player.

Gregb
#4

I've got one, but I think it's missing something there, too.

I'll try to dig it out this weekend and take pics anyway.

PM me if I forget. I can't begin to say how busy I am recently, but I'll be happy to help.

It's not how bad you mess up, it's how well you can recover.
#5

I have the 41-608 with the correct changer. I am also working on another of the same changer over the weekend. Pm me and I will take a look at it. My changer has perfect speed, but after it cycles and starts to play the record, the tone arm abruptly shifts back to the right, which I cannot seem to stop. Does yours do that?
#6

David, I am not to the point where I can see if the cycle works properly or not. Sad to say I have so many projects at the moment that I am not sure when I will get back to the BOL. Truth be told I have owned it for 15 years and so far havent spent more than an hour working on it.

Gregb




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Do make sure that you twist the 3 wires from the chassis to the transformer, and dress away from tubes, especially audio...MrFixr55 — 07:38 PM
Philco model 38 code 121 not receiving signal.
The cone unfortunately got damaged when I removed it. The glue that held the cone to the basket was sloppily applied and...Stormlord5500 — 07:12 PM
Philco model 38 code 121 not receiving signal.
So what was wrong with the original speaker? Was the cone damaged? Unless it's totally hopeless I would put it aside as ...Arran — 05:31 PM
My collection presentation
There is an article on my site that introduces the first portable radios in my collection. I have only provided a link t...Vlad95 — 01:17 PM
Electrolytic restuffing/internals
Bridkarl This specific cap you have is the easiset type to restuff. I usually cut it at the upper border of the depr...morzh — 11:35 AM
philco predicta
Hi CGL18, First off, welcome to the Philco Phorum. I have not worked on a TV for a while but here are some givens: ...MrFixr55 — 08:22 AM
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM

[-]
Who's Online
There are currently 701 online users. [Complete List]
» 1 Member(s) | 700 Guest(s)
Avatar

>