Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Help with radio problem
#1

Hi all, I hope someone will be able to help me here. I have a Philco model 91L, type 127. It's a low boy console. I recapped, checked resistors, etc. about twenty years ago. Anyway, I had it on the other night and suddenly the audio just stopped. I turned it off and back on and it seemed fine for about 15 minutes. The audio just stopped again; while going over to the radio, I noticed a blue/purple glow from the back of it. There was no odor at all nor did I hear any arcing or the such. I removed the chassis today and gave it a very close visual inspection which showed nothing at all. I'm afraid to turn it back on as I may do damage to it. Does anyone know what may cause this problem? Any help would be greatly appreciated.
#2

Hi Tim,
Just a guess but I think I would look for a gassy tube in the audio section. My guess would be in the first amplifier. They produce a blue or purple glow when this happens. I don't think it would hurt to bring it up to look for it if you had some kind of limiting device such as a variac or a dim bulb tester. Good luck Icon_biggrin

Terry
#3

If the high voltage is drawing too much current, the rectifier tube will often glow purple.

Your problem could be almost anywhere. I would pull and reinsert each tube to see if the purple goes away. That might get you to the circuit. Old components tend to break down over the years and develop leakage at high voltage.

If you get really desperate, I'm over here near Morristown and available most of the time. Parts, tubes, and equipment are here too.

Pete AI2V




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX.  They also had a 38-7T (table), and 38-7CS (chairside).  A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

[-]
Who's Online
There are currently no members online.

>