Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

A 38-15 fading triubleshooting
#1

This is the same one I restored aboyt 1-1/2 years ago.

When I set it aside, it was working but when the volage in the Mains went above 115VAC, the reception would fade and become weak.

Today I decided to investigate.
Since it was fully recaped, I went straight to tubes and since 6A7 was changed before, I went past it.
The main suspect was 78 tube, the IF amp.

http://www.nostalgiaair.org/PagesByModel...013239.pdf

Plus, this is the only extra NOS tube I have from the whole setup.
I changed it, and, lo and behold, the symptom disapeared.

I put the old tube back and within 2 minutes it came back.

I rechecked the 78 on Hickok, it is fine, the TC is 1350.
I let it sit for a few minutes, no, no degradation.
And no gas.


I decided to take a look at AVC voltage. The grid of the 78 and 4th grid of 6A7 go to -2.9V or so first, then with the bad tube the voltage drops gradually rises to 0.7V. The sound weakens about 1.5V.

With the good tube the voltage stays about 2.8V all the time.

And the corelation with high AC votage in Mains - when I lower the voltage the AVC starts dropping again and the volume restores.

Well, it is 78. But...strange. Leakage at high plate voltage?
#2

Seems like the 78 is gassy or has grid emission. When the voltage rises it may reach the point where the gas ionizes and causes the control grid to go positive.

Tubes can develop some weird problems. I had a 39/44 tube that did something similar. Radio would play fine for a few minutes then gradually reduce volume. Found AVC line went from normal negative condition when receiving signal to slightly positive as it warmed up. Replacing the tube cured the problem.
#3

Yep, same thing.
The tester does not detect gas, in fact if anything, this tube exhibits zero movement when the second Gas button is pressed, whereas it is normal to see up to 1/2 div movement and I usually see at least some.

Could be grid contamination.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Model 70 Cabinet Trim
musar , Well if you have any more questions feel free to post away . Sincerely Richardradiorich — 08:56 PM
Model 70 Cabinet Trim
Although I have not made any cabinets or cabinet parts for a couple of years, I still have some parts left over, includi...Steve Davis — 06:26 PM
philcorepairbench.com - shadow-meter
Thanks Ron.fenbach — 02:43 PM
Model 70 Cabinet Trim
Thank you, Gary. Before making my original post, I had clicked on "Steve Davis Cabinets" only to find that it...musar — 02:25 PM
philco predicta
Welcome to the Phorum, cgl18! I am not your resource for television repair, but lots of friendly help is available here...GarySP — 02:12 PM
Model 70 Cabinet Trim
Welcome to the Phorum, musar! You can send Steve Davis a private message (PM). The site is at the top of the Home page...GarySP — 02:09 PM
Model 70 Cabinet Trim
How do I contact him? The only contact information for him I could find when searching online was a telephone number th...musar — 10:38 AM
philco predicta
Hello, good afternoon, I would like to ask what the possible problem could be if I don't have an image on the screen. I ...cgl18 — 10:19 AM
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM

[-]
Who's Online
There are currently 577 online users. [Complete List]
» 2 Member(s) | 575 Guest(s)
AvatarAvatar

>